Question about 2001 Chevrolet Impala

2 Answers

I am having a problem with my emergency flashers on my 2001 chevrolet impala, when i press the button for them to come on they work fine, but when I press the button for them to go off they go off but the blinking noise remains behind. It keeps on making the blinking noise even when the emergency flashers are off. When i turn my key off it goes off but when I turn my key on it comes on again. The lights are off but the sound it still there.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 216 Answers

There could be several causes for this problem. The first would be a faulty flasher switch. These switch do fail can be in the off position and still have one contact causing the flasher unit to click.
The second cause could just be a bad flasher unit. The flasher unit is located under the dash near you left knee just above the fuse panel.
If you turn the flashers on you should be able to located it under the dash by sound.
You can simply remove this to see if the clicking stops. But once removed you will not have turn signals. So i would suggest you purchase a new flasher unit, there are inexpensive and always good to have one around.
If after replacing the flasher unit you still have this issue I would test the flasher switch on the dash with a ohm meter or a volt meter to ensure that once it is off you do not have any voltage traveling through the switch. If the switch still has voltage on both sides after turning it off you will need to replace the switch.
It could also be a short, but this is not very likely.

Posted on Aug 07, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Good Evening Faith. General motors had problems with thier combination hazard switch. The reason it is called a combination hazard switch is because it is also your turn signal and hazard flasher. On the Oldsmobile Alero, pontiac grand am there was a recall, as far as the impalas and monte carlos I cannot say for certain. Your local parts house (autozone, Advanced, Oreilleys) should have them or be able to order it. That should correct your problem. Hope this helps.

Posted on Aug 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the emergency flasher and turn signal light relay located on a 05 Chevrolet impala


Either under the dash or under the hood. In one of the two fuse boxes. I would look under the hood fuse box first.

May 18, 2017 | 2005 Chevrolet Impala

1 Answer

Why does 2000 impala turn signals stop working?


I am told it is a relay in emergency flasher circuit.

The quick fix is to activate emergency flashers just for a few cylcles , a minute or two after car has been running. The directionals will work fine for the duration of that ride.

I have heard of peolple remvoving trim to get at switch, cleaning contacts and components of switch, but symptom eventually re-appeared. Cycling through e-flashers a few times works every time for me. - Rick Rock

Sep 01, 2014 | 2000 Chevrolet Impala

4 Answers

How to replace turn-signal flasher 2004 impala


Make sure you check the turn signal fuse, located at the driver's end of the instrument panel. You have to open the door, take out a screw, and the panel pops off. The 4th fuse down on the 3rd row from the left is marked TRN-SIG.

Aug 04, 2014 | 2004 Chevrolet Impala

1 Answer

Where is signal light flasher


On 2001 Chevrolet Impala 6cyl the Flasher is located behind left center of the instrument panel.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 25, 2011 | 2001 Chevrolet Impala

2 Answers

Turn signals don't flash, they just go on solid


You may have a bad socket or bulb either in the front or rear replace if you find the one that is not working. May also be your flasher hit your emergency flashers and if those do not work suspect the flasher.

Oct 11, 2010 | 2004 Chevrolet Impala

1 Answer

My emergency hazard flashers are giving me fits. When I press the buttong to turn them on they work fine, and when I press the button to turn them off they go off but the noise stay on. IT sounds like a...


There is a 4-way switch inside your steering column which controls the hazard lights the blinkers. If this switch is faulty your example is one thing that can happen. If the problem worsens you could lose all exterior lighting except the headlights. I had this happen to me one time.

Aug 07, 2010 | 2001 Chevrolet Impala

1 Answer

Turn signals are not working


Do your emergency flashers still work? Have you had a tech check the bulbs? It could be the bulbs, The flasher module that plugs in to your fuse panel or a fuse, faulty wiring< (which I seriously doubt)> or your blinker actuator on the steering column. I think its just a fuse but I could be wrong.

May 07, 2010 | 2002 Chevrolet Impala

3 Answers

I've 02 Chevy Impala and the turn signal won't work. It flashes somewhat but not consistent. How should I repair this problem?


Just press the hazard warning switch off and on and it will restore the blinkers. I don't know why this works, but it has saved me from the overzealous dealer service people who want to replace the entire steering column.

Feb 10, 2010 | 2002 Chevrolet Impala

1 Answer

1997 Chevy Tahoe both turn signals stopped working


Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Jul 21, 2009 | 2001 Chevrolet Tahoe

Not finding what you are looking for?
2001 Chevrolet Impala Logo

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...