Question about 2002 Ford Super Duty F 450
This is called a spanner socket, It's a socket see image http://buy1.snapon.com/catalog/item.asp?store=snapon-store&item_ID=66782&group_ID=1663
This item can be rented from Orielly's auto parts or Autozone. Or you should purchase on from the local tool distributor. This spanner nut is used on the front and the rear wheels. Price is anywhere from $45 -$90 fora good socket respectively.
Posted on Aug 07, 2010
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Apr 03, 2015 | 2003 Kia Sedona
Before raising the rear of your Honda, remove the dust cup from the center of the brake drums using a hammer and chisel. This will give you access to the spindle nut, which you can loosen using an axle nut socket. Then you can raise and remove the wheel/tire assembly ,or assemblies if you are replacing the bearings on both wheels.
If your Honda model is equipped with rear disc brakes, remove the brake disc retaining screws, the brake hose bracket from the steering knuckle and caliper bracket mounting bolts. Hang the caliper to the coil spring using wire. Do not let the caliper hang free or the brake hose may be damaged.
At this point, you will be able to remove the brake disc by hand. However, rust may have a firm grip on the disc. If this is the case, use a couple of 8-by-1.25 mm bolts and screw them evenly into the brake disc threaded holes. This will push the disc off the hub. Now you can finish removing the spindle nut and hub/wheel bearing assembly and install the new hub/wheel bearing assembly using a new spindle nut
If your Honda Civic comes equipped with rear brake drums, remove the center grease cup and loosen the axle spindle nut using an axle nut socket. After raising and removing the wheel/tire assembly, finish removing the axle nut and washer.
You might be able to remove the outer wheel bearing from the spindle using a screwdriver. If not, wiggle the brake drum as you pull on it to let the bearing fall off the spindle. However, the brake drum might be caught in place by the brake shoes. In this case, you can retract the brake shoes through the hole in the back of the backing plate.
Remove the rubber plug from the back of the backing plate. Then rotate the star wheel on the adjusting screw using a brake adjusting tool as you push the lever off the start wheel with a screwdriver. With the brake shoes off the brake drum, pull the brake drum off the wheel assembly. Then clean the brake assembly with brake parts cleaner and a clean, lint-free towel.
Now you can set the brake drum on a workbench or hard surface and remove the grease seal and inner wheel bearing. The inner and outer wheel-bearing races can be removed using a drift punch and hammer. Pack the new wheel bearings with high-temperature wheel-bearing grease using a wheel-bearing packer and use a new grease seal during installation. Also, before reinstalling the brake drum, apply a thick coat of wheel-bearing grease to the cavity inside the hub, but do not fill it completely.
Aug 25, 2011 | Honda CR-V Cars & Trucks
May 28, 2011 | Ford Fusion Cars & Trucks
Rear hub and bearing
Click to Enlarge
Rear hub and bearing
Click to Enlarge
Rear hub removal
Inner wheel bearing removal-rear hub/bearing
Rear wheel bearing removal-2wd
Rear wheel bearing removal-4wd
Install or connect the following:
Rear wheel bearing installation
hope this helps if so send testimonial comment or even any other questions you have
Jan 16, 2011 | Ford Escape Cars & Trucks
Jan 01, 2011 | 2002 Mazda Protege
Dec 31, 2010 | 2004 Ford F150
Oct 28, 2010 | 2001 Hyundai Sonata
May 04, 2010 | 1998 Ford Windstar
Feb 06, 2010 | 1990 Mercury Topaz
May 30, 2009 | 1999 Hyundai Sonata
Aug 20, 2017 | 2002 Ford Super Duty F 450
167 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: