Question about 1996 Pontiac Sunfire

1 Answer

How do i get gas lines off fuel pump the seem to be like shrunk on can i cut and splice them ??

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Pontiac Master
  • 14,036 Answers


Posted on Aug 07, 2010

Testimonial: "great i was worried it looks like a reel pain to try to use this **** over thank you I have never run into anything like this before"


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2003 Hyaundi Sante Fe that developed a gas leak. I can see the line that has a pinhole in it. Can I cut out the bad part and splice this?

most times that will not work. the pressure is to high. I do not advise it. replace the whole section till you get to a mechanical junction fuel leaks cause fire and explosions.

Aug 20, 2014 | Cars & Trucks

1 Answer

The wires going to the plug that goes in the maf sensor on my 96 Nissan pathfinder are cut in two. can they be spliced or should they be replaced in order for maf to work?if replace CAN SOMEONE WALK ME...

Why would you think wires can't be soldered
& heat shrunk?

Where would you get other wires anyway !

Have to cut them off at a salvage yard & then
still have the splice & solder thing to do

Aug 30, 2013 | 1996 Nissan Pathfinder

1 Answer

I have a 1992 chevy silverado 1500 4.3l and it acts like it doesnt get gas and wont accelerate

Your catalytic converter might be clogged. Take it to an axhaust shop and have them test the amount of pressure before and after the cat. I guess you could cut off the converter and see how it does, but you better get it welded back on before someone calls the police on you!

Mar 24, 2013 | 1992 Chevrolet K1500

1 Answer

Gas line is leaking, can i splice it or do I need to replace the whole line?

you can splice it, use a tube cutter and cut at a sextion where the line is good, use hi strenght fuel injection hose and clamps, use two clamps at each end, and fasten against vibration

Aug 19, 2010 | 1985 Chevrolet S-10

2 Answers

I have a 97 Jimmy 2dr 4x4 ..Not getting any gas ..

When you turn the key on you should hear the fuel pump run if not, (fuel pump should run for 2 seconds and turn off). first thing to check is your fuel pump cut off switch which goes off in case of an accident. Next thing to check on the fuel line is find a Schrader valve to check for fuel pressure. If you have pressure you may have a different problem. If you don't have pressure or not sure hooked up a test light to the Power Supply at the fuel pump. If the light goes on you have power to the fuel pump. You may have a clogged fuel filter. If the fuel pump is still not working you may have a bad fuel pump or bad ground. Splice a wire into the ground and grounded it. If the fuel pump doesn't work pull it out and manually test it. If the fuel pump does work check all your grounds and make sure their cleaning connected to the body good. If this does not work Get a wiring diagram to figure out where the problem is. Good luck

Jun 11, 2010 | 1997 GMC Jimmy

1 Answer

I have a F150 and I replace the fuel pump, Sending

Put the old connector back on,and get the oem pump that installs without cutting and splicing

May 04, 2010 | 1992 Ford F150 SuperCab

2 Answers

85 Bronco 351w fuel leak

Sounds like you are rusted out. Even the factory parts are not that expensive and they are properly bent. Check the dealer.
If substituting aftermarket piping you want to either replace the bad section with a splice or the whole piece. Notice the end connections and where you will attach the replacements.
Notice the routing of the gas line away from hot exhaust parts and areas a lift jack will crush your line. Notice what moves close to the fuel line to allow for travel.

You may be able to splice a piece of rubber fuel line into a metal line with a few clamps.

I have seen everything you will need at Autozone and Oreillys and similar stores with the exception of Factory parts.

Sep 13, 2009 | 1985 Ford Bronco

2 Answers

Fuel pump problems

please give us a little more info so we can better help you...

Aug 07, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
1996 Pontiac Sunfire Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides