Question about Ford Ranger

1 Answer

I cant find the egr valve or the correct engine picture for a 4.0 1999 ford ranger xlt super cab

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,511 Answers

It got up an left.

Posted on May 09, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: vehicle will not start

check to see if the fuel pump is running all you have to do to caheck it is open the fuel door and take out the cap turn the key to the on position and have someon listen for it to start up if it does check to see if the timing belt is turning. If its not its your timing belt

Posted on Jun 18, 2008

  • 718 Answers

SOURCE: Where & how many oxygen sensors do I need for my 1997 Ford Ranger XLT Super Cab

Look before and after the catalytic converters. They will have wiring connected to them.

Posted on Apr 20, 2009

badealer888
  • 414 Answers

SOURCE: Ford Ranger overdrive light flashes

It could be anything,untill you get it scanned you will be just wasting money and time.
Tech note: if it is something simple and you wait it will destroy more.$$$

Posted on Jul 07, 2009

geharbison
  • 101 Answers

SOURCE: How do I remove step by step the gas tank of a

If you are needing to remove the gas tank to replace it, then you will need to empty the tank if you are able. You can buy a pump to siphon the gas for about ten dollars. Put a jack under the tank and jack it up to the tank just enough to barely put pressure on it. After that unbolt the two straps that hold it up. Remove the straps and slowly let the tank down. Try your best not to break the gas lines. Let it down far enough to see the gas pump. If it has a metal ring with little tabs on top of the pump. Take a hammer and a screwdriver and carefully tap on the tabs of the ring and move it until it releases the pump. If it is a snap ring holding the pump it, you will have to buy a special pair of pliers to get it out. A snap ring looks like a washer that has one gap in it, with two little holes on either side of the gap. If you are only wanting to remove the fuel pump, it is actually easier to remove the bed. To do that, undo the taillights and pull the wires through the bottom of the bed, and undo all of the bolts holding the bed down. If you do have to remove the tank, removing the bed will still make it easier, as well as greatly reducing the change of breaking a fuel line. good luck!

Posted on Jan 24, 2010

Testimonial: "Thanks for your courtesy in answering real fast. The real problem is that I have to change the filler hose which most probable is cracked ."

  • 123 Answers

SOURCE: I have a 1999 ford ranger 2 wheel drive automatic

If the temp / fuel gauges work then it just might be chance, just check you fuses first with a proper 12 v test light,

Failing that did you disconnect the battery for any reason?

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford ranger xlt valve clearance


These are hydraulic valves, there is no clearnace adjustment.

Dec 30, 2011 | 2002 Ford Ranger Regular Cab

1 Answer

Either code 4000 or 1400 on 2002 ford ranger 4.0 ltr v6. the right code should equate to the egr valve. I have replaced the egr valve but check engine light comes on again after reset showing same code.


code p1400 is a DPF EGR sensor CIRCUIT LOW VOLTAGE detected. most likely is a problem with the wiring to the egr or dpfe sensor. the pinpoint tests for code p1400 instruct you to test all wiring before replaceing the egr or dpfe sensor

Jan 19, 2011 | 2002 Ford Ranger Regular Cab

1 Answer

I need to know if my 2003 ford ranger 3.0 liter engine has a egr valve and where is it located


yes you have egr valve
its on the passenger side of the motor back at the fire wall
you can also locate it by looking at you exhaust
you will see a tube that goes from the exhaust up the fire wall and into the egr hope this helps
give feed back

Dec 28, 2010 | 2003 Ford Ranger Regular Cab

2 Answers

Locate Fuel Filter on 2005 Ford Ranger XLT


on my 05 ranger v 6 single cab the fuel filter is located on drivers side mounted in the frame.

Oct 09, 2010 | 2005 Ford Ranger

1 Answer

2000 Ford Ranger- engine stalling when slowing down to idol


replace th air idle bypass valve this is located on the throtle body and has 2 screws with 1 plug with 2 wires to it

Dec 29, 2009 | 2000 Ford Ranger SuperCab

1 Answer

1995 ford ranger Xlt it idles like its missing but when i put in drive and drive off its fine i tried injector cleaners ran higher octane did wires plugs cap/rotor cheacked all the leads im hoping its a...


they have egr issues that cause that they also have valve issues that could cause that! i have replaced a few injector here and there also so i would start there and then go to the egr valve! and so on...

Sep 18, 2009 | 1995 Ford Ranger Supercab

1 Answer

My egr valve


driver side front of intake hidden by black plastic cover look for small hose coming from exhaust to egr valve

May 19, 2009 | 1993 Ford Ranger SuperCab

2 Answers

Where & how many oxygen sensors do I need for my 1997 Ford Ranger XLT Super Cab


Look before and after the catalytic converters. They will have wiring connected to them.

Apr 20, 2009 | 1997 Ford Ranger SuperCab

2 Answers

What feels like a slight miss when you put a load on the engine...2.3L


it will not be egr valve ,check the timing of the engine first and eliminate this then make sure you have used the correct plugs then start looking at, oxygen sensor , air flow meter but check timing first

Jun 30, 2008 | 2002 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...