Question about 2000 Ford Taurus

1 Answer

I need a serp belt diagram for a 2000 Ford taurus wagon 3.0 DOHC engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 880 Answers

I need a serp belt diagram for a 2000 Ford taurus - 99387_taurus_v6_belt_1.jpgHere it is.

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the vacumn lines diagram for an 03 ford taurus wagon with a 3.0. 24 valve dohc v6 engine


All 2003 Ford vehicles were shipped with vacuum line routing diagrams printed on a sticker, which should be affixed inside your engine compartment. It is important that you use THAT diagram, as vacuum routing varies widely from vehicle to vehicle depending upon options and regional configuration.

May 22, 2015 | 2003 Ford Taurus

1 Answer

Need serp. belt diagram for a 2000 ford escort zx2 dohc


If your diagram is missing from under the hood, I can give you a few tips that may help get your belt installed. (1) The belt will wrap almost completely around each pulley, no pulley will be wrapped less than 2/3 of the way around. (2) The ribbed side of the belt rides in the grooves of the pulleys, and (3) The flat side or back side of the belt wraps around the smooth pulley or pulleys. Usually at least the belt tensioner pulley is smooth and runs on the backside of the belt. You may want to start at the crankshaft pulley by determining which pulley on either side of the belt will provide the most wrap around the crankshaft pulley.Hope this gets you on the road.

Jun 16, 2011 | Ford Escort Cars & Trucks

1 Answer

I need a diagram to put a surpetine belt on a 2000 for taurus DOHC


Visit this link to see the right diagram serpentine belt: diagrams/ford/taurus/2000

Hope helps (remember to rate this answer).

Apr 07, 2011 | 2000 Ford Taurus

1 Answer

I need a diagram of how the plug wires are put on 1999 ford taurus station wagon


1999 Ford Taurus 3.0 liter V-6 VIN "2"

zjlimited_234.gif


1999 Ford Taurus 3.0 liter V-6 DOHC VIN "S"
and
1999 Ford Taurus 3.0 liter V-6 VIN "U"

zjlimited_235.gif


Hope helps (remember to rate and comment this answer).

Mar 07, 2011 | Ford Taurus Cars & Trucks

3 Answers

I need a belt routing diagram for a 2000 ford taurus 24v dohc engine. Know where I can find one on the web? (No sticker under the hood. And I was dumb enough not to pay attention when I took it off.)


OK, one doesn't need a belt routing diagram to reinstall a new belt.

Just route the belt so that one by one you put the ribbed part of the belt up against the ribbed pulleys, and the smooth part of hte belt up against the smooth pulleys. Do this until one arrives at the tensioner and release tension with a breaker bar to put the belt on the final tensioner pulley.

Check that the tensioner has enough spring load for the belt to maintain the right friction against all of the serpentine pulleys.

That's all there is to it.

Sep 09, 2010 | 2000 Ford Taurus

1 Answer

I need a Serpentine belt diagram for a 2000 Ford Taurus 3.0L DOHC Duratec engine


It is not printed on a sticker on the cross bar in the front of the engine compartment where the hood latch is?

Thanks for your interest in FixYa.com

Mar 02, 2010 | 2000 Ford Taurus

2 Answers

Hello, does anyone have serpentine Belt routing diagram for 2000 taurus?


It is going to depend on which engine you have 24VDOHC or the push rod 3.0. Here is a possible link. There were few changes from 200-2003.
http://www.taurusclub.com/forum/uploads/monthly_06_2009/post-18292-1244426397.jpg

Dec 22, 2009 | 2000 Ford Taurus

2 Answers

Misfire on cylinder 6 on a 2002 ford escape 3.0 6 cylinder DOHC


the back side is from front(passenger side) of engine 1,2,3
front side is 4,5,6

Mar 17, 2009 | 2000 Ford Taurus

1 Answer

Need diagram for placement of serpentine belt for 97 Ford Taurus


Auto Zone has that information on line here. You didn't say what size engine you have or whether it is OHV or DOHC, but according to their numbers, almost 90% of 97 Taurus are 3.0L OHV.

Feb 10, 2009 | 1998 Ford Taurus

Not finding what you are looking for?
2000 Ford Taurus Logo

Related Topics:

420 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...