Question about 2007 Toyota Tacoma

1 Answer

How to remove the starter from a 2007 toyota tacoma?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 158 Answers

Hi,

1.Raise the hood of your Tacoma. Disconnect the negative battery cable with a wrench and isolate the cable away from the battery
2.
Raise the hood of your Tacoma. Disconnect the negative battery cable with a wrench and isolate the cable away from the battery

3.
Remove the nut securing the battery cable to the starter body with a wrench. Pull the battery cable off the post away from the starter. Pull the other wiring connection straight out of the connector.

4.
Remove the mounting bolts securing the starter body to the bell housing with a socket and ratchet. Support the starter body while you remove the mounting bolts, then pull the starter out of the bell housing.



Good luck!!!

Posted on Aug 06, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 55 Answers

SOURCE: replace starter

Disconnect the battery, then crawl under the truck and locate the starter, remove the plug going to the solenoid (small brown lead w plastic clip) . then the power wire that goes from the battery to the main starter terminal (12 mm nut) locate the 2 starter bolts 14 mm and unbolt the starter and remove. install in reverse order. ON the 4 wheel drives you may need to remove the skid plates over the bottom of the engine to access the starter.

Posted on Aug 25, 2009

  • 37 Answers

SOURCE: replacing front struts on a 2007 toyota tacoma

REALLY HARD PROJECT, TAKE IT TO SEARS, IT WILL ALSO NEED FRONT ALLIGNMENT

Posted on Jul 25, 2010

  • 55 Answers

SOURCE: HELP WITH REPLACING STARTER ON A 97 TOYOTA TACOMA 2.4 MAN. TRANS

http://www.tacomaterritory.com/forum/

Posted on Aug 24, 2009

  • 4 Answers

SOURCE: How do you change the spark plugs on a 2007 Toyota Tacoma?

bring it to a garage

Posted on Jun 05, 2009

ZJLimited
  • 17970 Answers

SOURCE: how to remove starter from 1997 toyota tacoma

REMOVAL & INSTALLATION

On all engines except the 2UZ-FE, the starter is external, mounted in a conventional manner, alongside the engine block. One the 2UZ-FE, however, the starter is mounted in the 'V' of the engine, between the cylinder head banks. The entire intake manifold assembly must be removed to access the starter motor and solenoid. (Toyota calls the solenoid a "magnetic switch.")


Except 2UZ-FE Engine

c56e5f2.jpg

Fig. Unfasten the starter mounting bolts . . .

6ecc4db.jpg

Fig. . . . then pull the starter toward the front of the vehicle to remove it (other components removed for clarity)

  1. Disconnect the negative battery cable.
  2. Remove the nut and disconnect the battery cable from the magnetic switch on the starter motor.
  3. Detach the remaining electrical connections at the starter.
  4. Remove the nuts and/or bolts securing the starter to the bell housing, and then pull the starter toward the front of the vehicle to remove.

To install:
  1. Insert the starter into the bell housing being sure that the starter drive teeth are engaged with the flywheel teeth, NOT jammed against the flywheel.
  2. Tighten the attaching hardware to 29 ft. lbs. (39 Nm) and replace all electrical connections.

f8fca87.jpg

Fig. Exploded view of a common starter mounting found on Toyota trucks
  1. Connect the positive battery cable (starter wire) to the starter.
  2. Connect the negative battery cable.

2UZ-FE Engine

ae7791c.jpg

Fig. The starter motor on this 2UZ-FE engine is installed under the intake manifold between the cylinder heads, making it a lengthy procedure to perform
  1. Disconnect the negative battery cable.
  2. Remove the cosmetic/acoustic engine cover.
  3. Disconnect the accelerator cable and intake air connector.
  4. Remove the intake manifold assembly. For additional information, please refer to the following topic(s): Engine Mechanical, Intake Manifold.
  5. Remove the two bolts holding the starter motor to the engine block and lift the starter away from the block.
  6. Detach the electrical connectors from the starter and remove the starter from the vehicle.

To install:
  1. Installation is the reverse of the removal procedure. Make sure all electrical connections are tight and that the harness is secure.
  2. Install the starter and torque the two bolts to 29 ft. lbs. (39 Nm).
  3. Install the intake manifold.
  4. Connect the negative battery cable.

Hope this help (ermember rated this).

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to I change the starter in 1997 toyota tacoma 4 x 4


Try this site. I found it on the Tacoma site.

http://www.tacomaworld.com/forum/1st-gen-tacomas/178029-how-remove-install-starter-fix-clicking-starter-2-7-liter-3rz-fe-engine.html

Nov 11, 2014 | Cars & Trucks

1 Answer

I have a 1998 toyota tacoma and have successfully removed starter from engine but cant remove it from engine compartment


Hi,
You can remove it by way of going under the engine or your car.
Hope that solve your predicament!

Dec 08, 2010 | 1998 Toyota Tacoma

1 Answer

Replacing front struts on a 2007 toyota tacoma


REALLY HARD PROJECT, TAKE IT TO SEARS, IT WILL ALSO NEED FRONT ALLIGNMENT

Jul 25, 2010 | 2007 Toyota Tacoma

1 Answer

Replace starter


Disconnect the battery, then crawl under the truck and locate the starter, remove the plug going to the solenoid (small brown lead w plastic clip) . then the power wire that goes from the battery to the main starter terminal (12 mm nut) locate the 2 starter bolts 14 mm and unbolt the starter and remove. install in reverse order. ON the 4 wheel drives you may need to remove the skid plates over the bottom of the engine to access the starter.

Jun 22, 2009 | 1999 Toyota Tacoma PreRunner

1 Answer

Whats the easiest way to change the starter on a 1999 Toyota Tacoma?


Remove the driver side front wheel was the best way to gain access to the starter which is right there. After removing the bolts there was a lot of twisting to get it out.

Have a great day!

Jun 18, 2009 | 1999 Toyota Tacoma PreRunner

1 Answer

Starter will not turn off, 1998 toyota tacoma


Either the starter has failed or you have a bad ground. I would say starter.

Jan 09, 2009 | 1998 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,968 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...