Question about Cadillac DeVille

1 Answer

Bank 1 and 2 lean and rapid misfire - DeVille Cadillac Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cadillac Master
  • 82,322 Answers

Vacuum leaks or lean fuel misture from defective MAP or MAF or ECT sensors

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

06 Cadillac STS V8 car has codes P0174 and P0420.


• DTC P0171 Fuel Trim System Lean Bank 1
• DTC P0174 Fuel Trim System Lean Bank 2
.
The engine control module (ECM) controls the air/fuel metering system in order to provide the best possible combination of driveability, fuel economy, and emission control. Fuel delivery is controlled differently during Open and Closed Loop. During Open Loop, the ECM determines fuel delivery based on sensor signals without oxygen sensor (O2S) input. During Closed Loop, the O2S inputs are added and used by the ECM to calculate short and long term fuel trim (FT) fuel delivery adjustments. If the O2S indicates a lean condition, FT values will be above 0 percent. If the O2S indicate a rich condition, FT values will be below 0 percent. Short term FT values change rapidly in response to the heated oxygen sensor (HO2S) voltage signals. Long term FT makes coarse adjustments in order to maintain an air/fuel ratio of 14.7:1. If the ECM detects an excessively lean condition, DTC P0171 or P0174 sets.
Diagnostic Aids
• Excessive resistance in the fuel injector ignition 1 voltage circuit or the fuel injector control circuit may cause the following symptoms:
- Lean condition
- Misfire
- Rough idle
• The system will go lean if an injector is not suppling enough fuel.
• A lean condition could be present during high fuel demand.
• A malfunctioning MAF sensor can cause this DTC to set. Refer to DTC P0101 .
• Review the Failure Records with a scan. If an intermittent condition is suspected, refer to Intermittent Conditions .

DTC Descriptors
This diagnostic procedure supports the following DTCs:
• DTC P0420 Catalyst System Low Efficiency Bank 1
• DTC P0430 Catalyst System Low Efficiency Bank 2

This code could mean the catalytic converter on that bank has failed .

Causes of lean condition trouble codes P0171 P0174 GM 5 3L

P0420 P0430 catalytic converter catalyst inefficiency code diagnosis

Mar 28, 2018 | 2006 Cadillac STS

1 Answer

I would like to know what these codes mean


P0171 System Too Lean (Bank 1)
P0174 System Too Lean (Bank 2)
P0301 Cylinder #1 Misfire Detected
P0302 Cylinder #2 Misfire Detected
P0304 Cylinder #4 Misfire Detected
P0306 Cylinder #6 Misfire Detected

Mar 12, 2014 | 1999 Ford Explorer

1 Answer

System to lean bank, manufacturer control fuel air metering, cylinder misfire detected


Intake or vacum leak will be the first codes 174,171, try idle and spray propane around intake if car idles up, then intake is leaking, otherwise could be a broken vacum line, check with a gauge

Jan 18, 2014 | 2004 Hyundai Tiburon GT V6

1 Answer

05 navigator codes po012 intake " A " camshaft position over ******** bank 1 po302 random misfire po302 cyl. 2 misfire po303 cly. 3 misfire po304 cyl. 4 misfire po2195 o2 stuck lean bank 1 sensor 1 po2196...


there is nothing wrong with the timing chain position . Just a series of sensors that have gone outside the set parameters so if you check and change each one you will clear the faults.

Jan 03, 2014 | Lincoln Navigator Cars & Trucks

2 Answers

What do I need done if codes p0171 p0174 p0301 p0305 p0316 is it major problems


OK, We'll cover the Diagnostic Test Codes (DTCs), starting with the standard definition set by SAE J2012 (Revised December 2007)
DTC P0171 "System Too Lean Bank 1"
DTC P0174 "System Too Lean Bank 2"
DTC P0301 "Cylinder 1 Misfire Detected"
DTC P0305 "Cylinder 5 Misfire Detected"
DTC P0316 "Engine Misfire Detected on Startup (First 1000 Revolutions)"

The "system lean" codes are pretty much telling you that there is way too much oxygen in the exhaust. There is too much oxygen on BOTH sides of the engine, and that is why you are getting codes for bank 1 and for bank 2. Bank 1 is the side where #1 cykinder is located and Bank 2 is the opposite side.

The misfire codes are pretty self-explanatory. #1 and # 5 cylinders are misfiring. The P0316 DTC is telling you that the misfire monitor is detecting a misfire as soon as the engine starts. This tells you that it is a very severe misfire and that the engine does not have to warm up and the car does not have to be driven to detect the misfire.

A misfire can be caused by many things it can be vacuum leaks, bad spark plugs, bad ignition cables, faulty ignition coils, fouled or malfunctioning injectors or injector circuits, blown head gasket, cracked cylinder head, burnt valves, etc.. etc..

However, look at the codes you have. Then look at the firing order for your engine. 2002 Mercury Sable is only equipped with a 3.0L 2V 6-cylinder engine.
The firing order is 1-4-2-5-3-6

Now if you take the firing order and split it in half, stack the two halves on top of each other, it looks like this:
1-4-2
5-3-6

When you look at the firing order this way, you can see that cylinders 1 an 5, 4 and 3, and 2 and 6, are "PAIRED" cylinders. They are exacly opposite in the firing order. Now, the cylinder only fires every second revolution of the crankshaft. With paired cylinders, one of the cylinders in the pair will fire on the first revolution and the other cylinder will fire on the second revolution.

Looking back at your codes, please note that the cylinders that are setting the misfire codes are paired cylinders.

Now the coil pack for your ignition is actually made up of three coils. Each coil fires a set of paired cylinders. If you look at the top of the coil, it will usually be marked with the cylinder numbers that each coil tower is supposed to connect to. The coil will look just like the firing order split and stacked as above.

With all of this said, I would say that it is VERY LIKELY that your misfire codes are being caused by a defective ignition coil.

The lean codes are a little different.

These are USUALLY caused by vacuum leaks which allow too much air into the engine that is not getting measured by the Mass Airflow (MAF) sensor and causes the engine to be getting too much air and not enough fuel (running lean).

I would take a good look at all of the vacuum hoses and lines. Ford is notorious for getting holes in the rubber parts that connect the PCV tubes.

If you do not find any obvious reasons for a vacuum leak, then you may want to fix the misfire codes, reset the computer memory, and drive the vehicle to see if the lean codes come back again. The misfires COULD be the cause of the lean codes. In a perfect world, this is not supposed to happen because the misfire monitors setting codes will not allow the oxygen sensor monitors to run and set lean codes. However, I HAVE seen cylinder misfires that have caused lean codes.

I hope this helps you to figure it out. Good luck!

Feb 03, 2012 | 2002 Mercury Sable

1 Answer

2001 gmc jimmy po171 lean bank code what could be the fix is it a possable o2 sensor


More than likely bank 1 sensor has a possible vacuum leak, or a lean misfire on that side of the bank.(lean misfire happens when gap of spark plug are exceed due to wear), As for the 02 sensor I agree that it is reporting the true engine condition on that side of the bank

May 01, 2011 | 2001 GMC Jimmy

2 Answers

P0313;Misfire Detected with low fuel P0171-System too lean{bank1} P0174 System too lean{bank2} drive cycle


P0313 - Misfire Detected with Low Fuel
P0174 -System too Lean (Bank 2).
P0171 -System too Lean (Bank 1).

P0171 and P0174 mean "system too lean" for banks 1

Aug 24, 2010 | 2000 BMW 3 Series

3 Answers

2003 Ford Ranger 4x4 extended cab- diagnostics checked and got these codes- P0171, P0174, P0300, P0316. Can you tell me what they mean?


P0171------ system too lean bank#1
Po174------ system too lean bank#2
For these 2 codes, try cleaning the maf sensor (mass air flow), that is mounted in the big black hose that goes from the air filter housing to the throttle plate, if it is dirty, that will cause those 02 sensors to send a signal to the computor to lean the air fuel mixture. If cleaning it doesn't work, the sensors will probably need changing.
P0300---- Random/multiple cylinder misfire
P0316---- Cylinder misfire at start up---- first 100 revolutions.
On those 2 codes, you have to do some testing to find out why there is a misfire.
Possible causes:
dirty/malfunctioning injectors
weak coil pack
fowling spark plugs/wires
Low fuel pressure

May 11, 2010 | 2003 Ford Ranger Regular Cab

2 Answers

98 camry engine light on w/misfires & system too lean


take sample of your fuel into clear plastic bottle from fuel line
is there any water present?
this can cause these codes and then not go on storing codes for other bank even though that bank will be missfiring also due to water & P0300 Random/Multiple Cylinder Misfire Detected being logged
check all connections to coils/leads & wiring connectors
due to miss fire codes for cyl 1,3,5 all on the same bank
also look and check for air leaks on that bank (hose knocked off or splithose)inlet manifold gasket,brake booster etc...
3 injectors being blocked slightly on same bank posible!!!
check wires and signal

was it running like this b4 tune up & repairs?
this is what codes are
P0170 Fuel Trim Malfunction (Bank 1)
P0300 Random/Multiple Cylinder Misfire Detected
P0301 Cylinder 1 Misfire Detected
P0303 Cylinder 3 Misfire Detected
P0305 Cylinder 5 Misfire Detected

the last code is for trans due to misfire/running lean on bank 1 probably a torque problem code
2e5d889.jpg

May 29, 2009 | 1998 Toyota Camry

3 Answers

Codes 1133-0131-0171-0300


p1133 - o2 sensor, Insufficiant Switching, Bank 1 Sensor 1.
p0131 - o2 sensor circuit, low voltage, bank 1 sensor 1
p0171 - Lean condition, Bank 1
p0300 - Random Misfire

I would be looking at the front passenger side oxygen sensor for issues. It may be bad, it may not be plugged in, bad wiring at harness.

The random misfire may be symptomatic of the o2 sensor problem.

Mar 17, 2009 | 2002 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

82322 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...