Question about 1999 Nissan Quest

1 Answer

1999 Nissan Quest. Driver side brake lock up. The mechanic replaced ABS, valve, caliper, master cylinder.....nothing seems working. The left front brake still lock. This is crazy. HELP.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

Possible brake hose collapsing , interrior deterioration

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is very little fluid going to the right side caliper on my 1997 Nissan Quest Van, what could be my problem?


Most likely the proportioning valve. They are usually located under the master cylinder. Some are mounted to the frame, some just hang from the brake tubing. This maybe be yours, but is what the look like.
25574891-g5cbwqkvwhrvkubdo54dykex-5-0.jpg

Mar 15, 2015 | Nissan Cars & Trucks

1 Answer

Abs brake system


Best case scenario bad vacuum pressure to the brake booster. Worst case bad abs control module or valve body/motor the abs system works by add and removing hydraulic pressure through valves and electric motor. Try using block off plugs at the master cylinder( remove lines plug outlets at master cylinder) check if brake pedal position and pressure is good(if there is no change problem is master cylinder or brake booster/ vacuum) if plugging at master cylinder solved issue repeat procedure at abs valve body after reinstalling lines from master cylinder if your problem returns your issue is in the abs valve body if plugging at the abs solves problem reconnect at the valve body bleed each line one by one testing between each line until you find the problem

Apr 11, 2014 | Hyundai Cars & Trucks

1 Answer

94 nissan quest front left brake locks up replaced front calipers and bleed the front same problem


I ran into that problem and it was because I put a pair of vice grip on the rubber brake line and it tore the inside of the rubber hose and wouldn't allow the brake fluid to return to the master cylinder, I don't know if you have the same problem but it's a idea.

Aug 26, 2011 | Nissan Quest Cars & Trucks

1 Answer

1996 Nissan Quest GXE model. Bleeded brakes. No parts replaced. Brake works normally. No drag. With ABS. Now, right rear wheel and left front wheel locks. left rear wheel and right front wheel turns...


you need to first adjust rear brakes per TSB in our file, 98-14=4 I think. (If you replaced or adjusted rear brakes)

Then bleed again, but you may need to loosen the pressure valve on the master cylinder, or apply very hard pressure on the dowm stroke with the front bleeder on the claiper open just slightly. You have to overcome the the valve spring in it as it is deisgned to send pressure to the rears before the fronts to allow the rears to engage at the same time as the fronts. It takes higher pressure on bleeding to over come.

go here for help

http://groups.yahoo.com/group/villagerquest/

Dec 13, 2010 | 1999 Nissan Quest

3 Answers

1999 nissan quest brakes over heating


even though the parts are new they can still be bad the calipers are sticking have him replace them at no cost due to part being bad if he says no then go elsewhere

May 14, 2009 | 1999 Nissan Quest

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

2 Answers

2001 nissan quest brakes


You need a scan tool to hold open the control valves in the ABS, air is trapped in it and you can't bleed the brakes until you have the ABS held open

Apr 12, 2009 | 1999 Nissan Quest

2 Answers

1999 nissan quest brake pad replacement


Remove wheel & tire,
remove 2 torx bolts that go from the inside to the outside of the vehicle. They are on the inner side of the brake caliper.
lift the caliper out of the rotor.
remove the brake pads.
To install, you must first squeeze the caliper piston back inot its bore. Do this slowly to prevent damage to the piston. You are forcing excess brake fluid back into the master cylinder reservoir. Slow constant pressure will get the job done. Use a large c clamp or a wooden hammer handel if that's all you have.
Fit the new brake pads in the calipers and slide the assembly back over the rotor.
install the 2 torx bolts, size 40? head I think.
You are done.
If rotors are scored bad, replace them too.

Jun 07, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
1999 Nissan Quest Logo

Related Topics:

583 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...