Question about 1998 Chevrolet Monte Carlo

1 Answer

How to install crankshaft sensor for my 98 monte carlo

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Normally the cranshft senosr is located between the engine bell housing in between the transmission case. Look at the image photo on yahoo or google.. You will figure out what I'm trying to say.

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor on a 2003 Monte Carlo 3.4 engine


Behind the lowest pulley on the engine. This is the crankshaft. Remove the belt. Remove the tire on the passenger side along with the plastic coverings for the engine. Remove the bolt holding the pulley Use a pulley puller to pull the crankshaft pulley off. Remove the sensor on the right side if the of the shaft.

Oct 03, 2014 | 2003 Chevrolet Monte Carlo

1 Answer

We have a 1996 3.1 we replaced the crackshaft sensor on it but it still cracks and backsfire when tring to start what else could we do


It is not the sensor: The problem is in the fuel adjustment, timing, and/or gas line filter, etc. Too many reasons and needs a total checkup.

May 09, 2014 | 1996 Chevrolet Monte Carlo

2 Answers

We have a 1996 3.1 monte carlo ls we need to replace the crankshaft senor but we cant find it on the motor is there a picture of where one could be


The crankshaft position sensor is a two pin sensor made up of plastic like material. It is located on the back side of the engine block about half way between the oil pan and the top of the block. It can only be accessed by crawling under the car. 33899bbd-15f1-451a-9a7a-a94f8be62e27.png

May 07, 2014 | 1996 Chevrolet Monte Carlo

1 Answer

2000 monte carlo no gas no spark new fuel pump good modual and coils help! camshaft crankshaft???


No gaurantees, but it most likely needs a crankshaft sensor. That sensor triggers both the spark and the fuel injectors.

Feb 22, 2010 | 2000 Chevrolet Monte Carlo

1 Answer

Crankshaft sensor on a Monte Carlo 2001 SS 3.8 where is this on the car and how to replace it?


3.8L Engine
  1. Turn OFF the ignition.
  2. Remove the serpentine belts from the crankshaft pulley.
  3. Raise the vehicle.
  4. Remove the right front wheel and tire assembly.
  5. Remove the right inner fender access cover.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  8. Remove the crankshaft harmonic balancer, using a (J 38197-A) balancer remover.
  9. Remove the crankshaft position sensor shield (1). Do not use a pry bar.
  10. Disconnect the sensor electrical connector.
  11. Remove the attaching bolts from the crankshaft position sensor.
  12. Remove the crankshaft position sensor from the block face.
To install:
  1. Position the crankshaft position (CKP) sensor to the block.
  2. Install the bolts to hold the CKP sensor to the block face. Tighten the bolts to 14-28 ft. lbs. (20-40 Nm).
  3. Reinstall the crankshaft position sensor shield.
  4. Connect the CKP sensor electrical connector.
  5. Position the crankshaft harmonic balancer on the crankshaft.
  6. Hold the flywheel with a (J 37096) flywheel holding tool.
  7. Using a (J 36660-A) torque/angle meter, tighten the harmonic balancer bolt to 110 ft. lbs. (150 Nm), plus an additional 76 degrees.
  8. Install the right inner fender access cover.
  9. Install the right front wheel and tire assembly.
  10. Tighten the wheel nuts to 104 ft. lbs. (140 Nm.).
  11. Lower the vehicle.
  12. Reinstall the serpentine belts.

It looks like this:

fd368a5.jpg

Jan 10, 2010 | 2001 Chevrolet Monte Carlo

1 Answer

98 Monte carlo Z/34 cranks immediately then cuts


start by check ignition module(controls spark) do fuel pressure check to see if pressure within specs

Oct 20, 2009 | 1998 Chevrolet Monte Carlo

1 Answer

98 monte carlo won't exceed 3000 rpms


Well both of you should look at the MAF sensor. It reads the air volume of the itake and adjusts the fuel accordingly. No air, No fuel, See if that helps

Sep 16, 2009 | 1995 Chrysler Concorde

1 Answer

Car just keep spinning


crankshaft sensor is located just above the crankshafy front dampener./ pulley

Apr 27, 2009 | 1997 Chevrolet Monte Carlo

1 Answer

I CANT LOCATE CRANK POSITION SENSOR


7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
Right hand side of engine, at end of crankshaft, behind harmonic balancer

Apr 12, 2009 | 1995 Chevrolet Monte Carlo

Not finding what you are looking for?
1998 Chevrolet Monte Carlo Logo

389 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...