Question about 1994 Ford Probe

1 Answer

Immobiliser appears to be faulty no spark no fuel.I would like to know how to disable the immobiliser please so that I can get the car to run. model is 2.5litre

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 11,800 Answers

First you need to take it out. It's located behind the centre console at floor level. No need to remove the centre console, just the 2 small side panels (1 screw, 1 clip). The immobiliser is attached to a metal plate secured by 2 rivets on the driver's side and 2 star screws on the passenger side. Once it's out you need to solder some wires as explained here:
http://probeimmobilizer.tripod.com/

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Causes of fuel pump failure


faulty relay. bad earth. or immobiliser not activating the power, and also be the wiring on some models under the rear seat. or the power feed to the pump if in the tank. or the pump has failed or blocked on the pick up.

Jun 25, 2018 | Cars & Trucks

1 Answer

91 4 runner immobiliser with an equator immobiliser


91 4 runner immobiliser with an equator immobiliser
I have a toyota4 runner which has an equator immobiliser now she won't fire have spark and fuel but won't start As old as this vehicle is you might think of replacing it with one that fires has spark and fuel.Goodluck )

Jul 20, 2016 | Toyota 4Runner Cars & Trucks

1 Answer

What do i neede to do


Before you race out and get a new distributor I suggest that you run the fault codes first to determine the fault as it may have nothing to do with the distributor. Lack of spark can be from immobiliser. cam/crank shaft position sensor , blown fuse. faulty coil and wiring problems . I would check to see if the cam shaft is turning to check for a broken timing belt/chain. Do the cheap checks first before you waste money on what is not faulty.

Jun 30, 2014 | 2000 Chevrolet Silverado 1500

1 Answer

1991 mitsibushi mini mac has no spark at spark plugs won't start.


spark is controlled by the cam/crank position sensors and the engine immobiliser . Check that the cam shaft is turning( broken belt/chain). Check that the immobiliser is operational. run fault codes to check for other faults that will stop spark--like faulty ignition module or coil/s.

May 19, 2014 | Cars & Trucks

1 Answer

It turns over but no spark


to check for timing belt see if you can watch the cam shaft movement through the oil filler hole while some one turns it over. If things move then have a code reader find the faulty sensor.. I would suspect faulty cam/ crank position sensor/wiring connections or engine immobiliser before a fuel pump

Dec 02, 2013 | Cars & Trucks

1 Answer

1996 DODGE 1500 PICKUP CHECK ENGINE LIGHT DOES NOT COME ON CANNOT GET FUEL PUMP TO RUN OR GET VOLTAGE TO THE COIL HAS BEEN SITTING FOR THREE YEARS REPLACED THE FUEL PUMP AND IF RELAY IS JUMPERED OUT THE...


have you checked the immobiliser. if the immobiliser fails the engine light will not come on or the fuel pump. it is linked to the engine ecu. if it fails or is faulty then replace and you will need to pair it to the engine ecu with a tecII and the car pass code. you can test the ecu etc on tec II just to make sure it is this as it will not pick up the immobiliser at all if it is not working.

Sep 20, 2013 | Dodge Ram 150 Cars & Trucks

1 Answer

1997 ROLLS ROYCE SILVER SPUR, CRANKS BUT DOESN'T FIRE.NO POWER AT FUEL PUMP,FUSES ARE OK.NO PULSE AT COIL PACKS.DOES THIS MODEL HAVE AN IMMOBILISER? IT DOES HAVE FACTORY ALARM,BUT NO MENTION OF...


it has a relay that disables spark and fuel when a sensor on the motor detects combustion gasses in the water, this system only usually cuts in after some driving but you could have a faulty relay, Rolls are good with wire colours so follow the wire colour from the fuel pump to the relays (I had the problem with a customers 1995, rolls were unhelpful so I had to do it the hard way!)

Aug 24, 2010 | 1997 Rolls Royce Silver Spur

2 Answers

Vw 2.6 immobiliser


My vw caravelle bus 2.6i -1996 model cant start- just cranking but not firing, cant hear the pump click as usual. It was just running fine, then switched off, when i got back all these started. kindly assist.

Dec 04, 2008 | 2005 Volkswagen Microbus

Not finding what you are looking for?
1994 Ford Probe Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...