Question about 1993 Buick Skylark

1 Answer

I have a 1995 buick lesabre and i changed control module,position sensor,cam sensor and computer. car stop and will turn but want start. when i first bought car it had this vibration on take off but never could find out what it was. need help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 6,826 Answers

Are you getting gas and spark to the cylinders?

If you add gas to the throttle body, does it start?
If so, then you have a fuel pump delivery problem in this vehicle.

If it doesn't start, then you may have a spark problem at the spark plugs due to a coil pack going bad or a module (but you said you changed the module).

Also, is this a 1995 Buick LeSabre of a 1993 Buick Skylark (which it is listed under)? What engine size is this?

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 geo wont start changed ignition module no spark but turns over


The other sensors whereby the computer controls spark timing, are the Crank Position Sensor, and the Cam Position Sensor (sometimes called the pick-up coil, inside the distributor).

Oct 30, 2012 | 1995 Geo Metro

2 Answers

1992 buick lesabre cam sensor location


it is on the timing cover just below the water pump but that normally causes a hard start check the crank position sensor behind the crank pulley

Aug 14, 2012 | 1992 Buick LeSabre

1 Answer

I have a 1995 buick regal custom: it has 70,000 miles on it ... When I'm driving at the speeds around 40 to 50 mph it seems to studder or something but when I take my foot off the accelerator it...


That doesn't sound like buick dealer response , not with the tools they have at thier disposal . This sounds like a ignition control module or one of the crankshaft position sensors (has two ) or possibly the cam position sensor . The buick dealer tech's should have a tool like this .
How to test crank sensor on GM 3800 engine 3x and 18x signals

May 04, 2017 | 1995 Buick Regal

3 Answers

1986 buick lesabre 3.8 won't start. no spark. Chaged cam sensor. Had module checked. Still no start


'86 does not need cam sensor to run. Besides cam sensor there is a pickup magnet on cam gear. Front cover must be removed to change. As long as asd relay is activating and wiring / fuses have been verified as good. Then I would suspect your crank sensor as faulty. A scan tool would be useful for this, as you could check cranking rpm's to verify.

Apr 26, 2011 | 1986 Buick LeSabre

1 Answer

1990 buick lasabre with a 3.8 engine, cranks but no spark. No voltage to the primary side of coil. Code shows 22. Changed the trottle position sensor, crank position sensor and cam position sensor. Had the...


1. Monitor the 5v reference, Gray wire to the Throttle Position Sensor (TPS) with a Digital Volt Ohm Meter (DVOM) set to the MIN/MAX setting.

2. Monitor the TPS signal circuit, Blue wire with a DVOM. Voltage should range smoothly from approximately 0.44 to 5.0 volts as the throttle is opened.

3. Tap test the Electronic Control Module (ECM) and see if the codes come back or if the engine reacts.

possible causes wiring or Powertrain Control Module (PCM)

Oct 31, 2010 | 1990 Buick LeSabre

1 Answer

2000 Buick LeSabre Will not start Replaced cam


Multiple engine misfire is related to the coils and the ignition control module. I have a 2002 with the 3.8 engine. It has three coils. I just went through this problem. I bought one coil and tried it in each position with no improvement. It was the ignition control module. Mine is located under the three coils. A relatively easy item to replace. Cost about $140.

Apr 18, 2010 | 2000 Buick LeSabre

1 Answer

1995 buick lesabre engine revs up very loud, then normal when


I saw exact same problem for few days. Now I see check engine light all the time and engine speed is normal.
The cruise control stopped working. Cruise control sign so nOT light up when I turn it ON. Nor does it works.
But car seems to work fine.

Mar 21, 2010 | 1995 Buick LeSabre

2 Answers

1994 Buick Lesabre shutting off


it's probably the crankshaft position sensor. these are notorious on the 6 cylinder gm engines. tell your mechanic to diagnose the car and stop changing parts

Nov 21, 2009 | 1994 Buick LeSabre

4 Answers

1995 BUICK LESABRE WON'T START


bad fuel pump, or fuel fuse/relay check fuse or relay first

Sep 27, 2008 | 1995 Buick LeSabre

Not finding what you are looking for?
1993 Buick Skylark Logo

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...