Question about 1999 Nissan Altima

1 Answer

Where is the knock censor located at - 1999 Nissan Altima

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Nissan Master
  • 14,036 Answers


Posted on Aug 06, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What does a knock censor control on my car and a camshaft censor

A knock sensor detection detonation and the computer responds by retarding spark timing. The camshaft sensor is used to compute injector and spark firing.

Jan 27, 2018 | Cars & Trucks

1 Answer

Where is the knock sensor

where is the knock censor on a 1991 brougham located

Jan 03, 2014 | Cars & Trucks

1 Answer

My Nissan 3.3 hard body cuts out totally when I drive replace the mass airflow censor but still it happens can it be my knock censor?

Best is to run the fault codes to find the faulty sensor rather than guessing what is wrong. Saves the dollars in the long term

Sep 29, 2013 | Nissan Cars & Trucks

1 Answer

1999 nisson maxima has knock cencer 2 wires coming from pigtail only one on censor ,is there suppodse to be two wiresd or how to dissconnect wires from knock censor

Hello! The Knock Sensor (see photo below) has a 2 wire connector...White is the Signal Lead and the second wire is the Shield Ground...It's a sensitive device...The shield has no color assigned but ties in to a common junction of Black chassis ground...It is located under the intake manifold..Guru..Saailer

12_6_2011_3_18_25_pm.jpgORIGINAL ENGINE MANAGEMENT Part # KS24...Cost=$80

I’m happy to help further over the phone at

Dec 06, 2011 | Cars & Trucks

1 Answer

Location of 2002 nissan xterra 3.3 knock censor

There are 2 knock sensors. They are located under the intake manifold in the right and left cylinder head.

Oct 04, 2011 | 2002 Nissan Xterra

1 Answer

Where do i find the location for the knock censor,is it on the block somewhere?

  • Most of the time they are under the intake manifold. I recommend a changing of the harness. Use the correct torque on these sensors as well. You didn't list your make and model of vehicle so I cannot say to a fault where yours is located but this is the most common place for them.

Regards, Tony

May 03, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

Knock censor have been replaced and still having problems with number 2 knock censor low input

HI . make sure the two sensors are replace from the dealer along with the harness going to the top of your intake and make sure they silicone the plastic grouments that cover the sensor holes to keep water .

Dec 23, 2010 | 2002 Chevrolet Silverado 2500HD

1 Answer

Where is the knock censor

the knock sensor is located on the left front side of the engine,the side closest to the firewall,should be screwed into the engine block Hope this helps,please rate my fix Thanks Ray. need more help get back to me

Feb 19, 2010 | 1996 Toyota Tercel

3 Answers

My 1997 nissan pathfinder p0325 code came up on the scanner, and I need to change my knock censor on the car. I do not known were this part is located on the engine

very familiar with this. it is down under the intake manifolds in the valley of the engine. it is a single wire connector. you must remove the manifolds to replace this item. parts will run you about $100 and take about 3-6 hours depending on your compentance. parts needed are 1. knock sensor 2. intake(upper and lower plenum gasket)set 3. coolant. make sure you drain your radiator prior to doing this as to not allow a bunch of coolant to drain into the cylinders and cause hydrolocking. if this happens you must remove the spark plugs and rotate the engine to spray out the liquid out of the cylinders then reinstall.

Dec 24, 2009 | 1997 Nissan Pathfinder

1 Answer

Knock censor

It should be on the back of the block

Oct 23, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
1999 Nissan Altima Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

81400 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides