Question about 1998 Dodge Intrepid

1 Answer

I have a 2001 dodge intrepid. I just replaced the output speed sensor. It is still stuck in limp in mode.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

There is a recall on some intrepids for the cam position sensor. You may have to change the cam sensor, if you don't have a code for it, don't change it. You might have to go to the dealer and have them flash your computer with a scan tool. that may be covered under the recall. I would investigate if I were you.

I hope this helps

Posted on Aug 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 caravan in limp mode sometimes


i have had luck replacing the solenoid packs on these models but i usually had a 12 shift or 23 shift code stored in the tcm controller

Dec 05, 2012 | 1994 Dodge Caravan

2 Answers

1997 intrepid automatic transmission stuck in 2nd gear try to auto shift and it also stays in 2nd gear fluids are good but check engine light is on.


There are two speed sensors on the drivers side of this transmission. If your speedometer is working, replace the input sensor (closer to the front of the car). If the speedometer is not working, replace the output sensor(closer to the rear of the car). Or they cost less than 20 bucks, replace them both while you're underneath the car. They are dissimilar, so you cannot put the wrong one in the wrong place.

Sep 04, 2011 | 1997 Dodge Intrepid

1 Answer

2002 Dodge Caravan stuck in Limp Mode. Changed input speed sensor, TCM and relays. Help me


Change the output speed sensor as well and clear the vehicle codes either via a scanner or disconnecting the battery.Also make sure the transmission is at the proper fluid level.

Aug 30, 2010 | Dodge Caravan Cars & Trucks

1 Answer

Speedometer quit on a 2000 intrepid. And it quit shifting gears at the same time


A common issue are the input and output speed sensors.When bad they cause the vehicle to go into limp mode keeping it in second gear and speedometer sometimes no longer works.

Jul 06, 2010 | 2000 Dodge Intrepid

2 Answers

My 91 dodge stealth is in limp mode how do i fix this transmission problem


Your car is in "limp"mode because the computer doesn't know what speed your doing,So it doesn't shift,
There are three possible reasons for this,
#1= input sensor faulty on transmission,
#2=output sensor faulty on transmission,
#3=speed sensor faulty on transmission,
you need to have the transmission codes read to know which one,Autozone checks codes for free.

Jan 13, 2010 | 1991 Dodge Stealth

1 Answer

Intrepid won't shift out of first gear, codes 0700, 0740, 0605


Your car most likely has gone into what is commonly called "limp in mode" The codes are transmission codes and you'll need to have it checked out and repaired. Something very common to Intrepids are the vehicle speed sensors going bad. If one or both go bad it will go into limp in mode and not shift properly. There is an input and an output speed sensor on these transmissions. Normally we would just change both because they are relatively inexpensive and easy to change. Hope that helps, gl.

Nov 24, 2009 | 2002 Dodge Intrepid

1 Answer

1998 Chrysler Intrepid ES 3.2 Code P0731.


Check the connection to the vehicle speed sensor. You can check the vehicle speed sensor by using a voltmeter set at millivolt. Then pass a metallic object close to it. The sensor should induce voltage as you pass the metallic object close to it. If not replace the vehicle speed sensor.

Nov 23, 2009 | 1998 Dodge Intrepid

1 Answer

95 dodge intrepid wont shift out of first gear


It sounds like the trans has gone into "Limp In" mode. You may need to access the trans controller and look at fault codes. A Generic OBDII scanner may give you the codes. You could also try disconnecting the battery which will reset the trans controller. (however that is not a cure but it will verify the trans was in fault mode) The most common issues I've seen have been with the "Input" and "Output" Turbine Speed Sensors. They are both mounted on the trans case (External). The input is towards the front and the output is near the rear.

Mar 30, 2009 | 1999 Dodge Intrepid

1 Answer

99 intrepid stays in 1st gear.


On the tranny there are input and output speed senors,it sounds like your input speed sensor went bad,this was a very common problem for those cars,and not very expensive to fix. The car is stuck in what they call limp mode.

Mar 29, 2009 | 1999 Dodge Intrepid

2 Answers

Limp in mode


you have to change the solenoid control if your car is 3.5 engine the solenoid control located at inside the transmission..

Aug 19, 2008 | 2004 Dodge Intrepid

Not finding what you are looking for?
1998 Dodge Intrepid Logo

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...