Question about 2002 Dodge Intrepid

2 Answers

Replacing 2.7 engine with 3.5 engine 2002 INTREPID. What engine code do I need for 2002 3.5 engine ?

Posted by on

  • roydie61 Aug 06, 2010

    I have a 2002 Dodge Intrepid with bad 2.7 engine which I want to replace with a 3.5, I was told engine would have to be a 02 or newer. There is a engine code G and engine code V for 3.5 in 2002's.
    I am told difference is intake and exhaust manafolds, which engine code do I need??
    I put a 3.5 from 2000 Chrysler veh into a 1999 Intrepid and also in a 2000 Intrepid. Bolt in deal, did not change computer and both veh runs fine.

  • roydie61 Aug 07, 2010

    Thank You very much this helped a great deal,

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 17,970 Answers

Engine code? I'm assuming that you are refering to the VIN code, if this its right, keep in mind that the 2.7 vs 3.5 have few VINs...

Dodge Intrepid 2.7 liter...
2.7 liter DOHC V-6 VIN "R"
2.7 liter DOHC V-6 VIN "U"
2.7 liter DOHC V-6 VIN "V"

2002 Dodge Intrepid R/T 3.5 liter...
3.5 liter SOHC V-6 VIN "G"

Hope helps.

Posted on Aug 06, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Dodge Master
  • 2,030 Answers

Any 3.5 engine can be used, but there are a few things you have to do...

Going from a 2.7 to 3.5 is not a direct swap-in....you have to change the computer(ECM), the entire wiring harness, and possibly the transmission and axle shafts. You will also need the heavier springs for the front end.

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 dodge intrepid 2.7. Code p0605. Changed tcm started car no service engine light. Pulled out but wouldnt shift into 3rd or overdrive still. Service eng. Light came back on now what do I do?


I can't remember what a PO605 code is off-hand, but I do know that it is a PCM code, and not a BCM code. There are 2 different computers.

Oct 29, 2013 | 2001 Dodge Intrepid

1 Answer

2001 dodge intrepid with p0201 code does the injector need replaced


Codes don't tell you what is wrong or have anything
to do with replacing parts

Codes are used to diagnose the system with the fault &
then component test

Feb 01, 2013 | 2001 Dodge Intrepid

1 Answer

1996 3.3l intrepid o2 locations


There two catalytic converters and two O2 sensors. Code PO154 Bank 2 sensor 1 which is the driver side sensor staying in the middle range, it might need replacing. Normally the O2 would go active or lazy but staying in the middle is new for me.

Jun 18, 2012 | 1996 Dodge Intrepid

1 Answer

Shift solenoid needs replacement according to chek engine computer check not shifting out of first gear


There are no computers used to diagnose a vehicle

If your referring to a scan tool & codes,the codes
do not tell you to replace something

They only indicate a possible malfunction
in a system

You then have to component test to find
out if something needs replacing

A trans shop or a really good local repair shop
is what you need

Any type of issue you believe is trans related,
calls for an immediate halt to using the vehicle,
unless you got 2 or 3 grand to part with

Jun 09, 2011 | 1997 Dodge Intrepid

1 Answer

I need to know how to pull the codes on my 99 Intrepid..I lost the manual that had the instructions.


After 1996, a scanner is required to get check engine light codes. Hooked up to your OBD-2 data connector.

Nov 19, 2010 | 1999 Dodge Intrepid

1 Answer

NEED TO REMOVE STARTER AND DON'T KNOW HOW


I found your solution (with pics) at:
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528006a865

However, www.autozone.com will expect you to register (free) to access their repair guide database.
Note: The Intrepid 3.5L engine takes the Delco starter, while the Intrepid 3.3L engine takes the
Nippondenso starter.
How can you tell which engine's in your Intrepid? read 8th digit of the VIN code.
VIN code "F" - 3.5L 6cyl MFI (multi-port fuel injection) - 60% of 1997 Dodge Intrepids sold
VIN code "T" - 3.3L 6cyl MFI - 40% of 1997 Dodge Intrepids sold

Oct 25, 2010 | 1997 Dodge Intrepid

1 Answer

Code says there is a problem with the camshaft sensor. Occassionaly the check engine light comes on and the car stops running or runs very rough


I also have a 04 intrepid with the 3.5L engine. mine did the same thing. I replaced my cam position sensor. Bought it at autozone for $30 and replaced it myself. It's located in your timing cover in front of the engine under your upper intake. Never had another problem after replacing it.

I hope this helps

Aug 05, 2010 | 2004 Dodge Intrepid

1 Answer

What is codes P016 Po441 P0135 2002 intrepid


016 is crankshaft position sensor. This needs to be diagnosed properly. Alot of times this part is replaced when an underlying condition is really the cause.
441 is an evaporative emmisions leak or a faulty purge or vent solenoid This vehicle also may have an vapor management valve so diagnosing is best so you dont replace the wrong parts when maybe the whole problem was a bad fuel cap or a vacuum leak somewhere.
And the 0135 is the 02 sensor heater circuit. This usually points to a faulty sensor and if so both upstream sensors will need replacing soon.
Now with all those codes I wonder if they happen all at once. There should be no way thier related but if they all happen at once I would start by removing the battery terminals and cleaning. And any grounds on the engine or body under the hood, clean them also. Most likely this isnt your issue but its the one thing you can do for free that might help. Then get the codes cleared. Disconnecting the battery may erase the codes.. If the codes come back you will need to get them addressed.

Nov 05, 2009 | 2002 Dodge Intrepid

1 Answer

Location of oxygen sensor


There is only 4 sensors on a 2000 dodge intrepid and the bank 2 sensor 2 is the sensor located on the right (passenger) side and the one located after the catalytic converter (the one close to the firewall).

Apr 08, 2009 | 2000 Dodge Intrepid

1 Answer

Check engine codes 95 dodge intrepid


Code 12 is: Direct battery input to PCM was disconnected within the last 50 key-on cycles.

Code 21 is: Neither rich nor lean condition detected from the oxygen sensor input or oxygen sensor input voltage maintained above the normal operating range.

May 22, 2008 | 1995 Dodge Intrepid

Not finding what you are looking for?
2002 Dodge Intrepid Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...