Question about 2000 Chevrolet Venture

1 Answer

Yes my 2000 chevy venture 3.4 ltr left me sitting. The oil pressure light and dingger came on just seconds before the engine stalled. I cannot turn the motor by hand,is there anyway to unsieze this engine?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

IM SORRY BUT THE ONLY WAY TO UNSIEZE AN ENGINE IS TO TEAR IT DOWN AND FIX THE PROBLEM. USUALLY WHEN U SIEZE AN ENGINE ITS A LOWER CONNECTING ROD BEARING OR CAM BEARING

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2002 chevy venture and the low oil pressure light came on with a loud dinging sound, shut the van off and now it wont crank


Did you check crankcase oil level? Did the engine over-heat? Is the engine seized? If the engine is seized, you may have internal engine damage? Can you turn the crank by hand? If you remove accessory belt and spark plugs, should be easier to turn.
I don't know if your oil pump might be faulty?

Cranking is starter motor action, engine turns over. When you talked about oil pressure, it got me worried, if that's ok, have a helper crank it while you check for spark at the spark plugs, if spark everywhere, use a gage and check proper fuel pressure. Also, check fuel injector pulse. Any applicable trouble codes?

Feb 25, 2017 | 2002 Chevrolet Venture

1 Answer

How to turn off change oil light on the 2004 Chevy Colorado Pick-up truck ?


1. Turn the ignition to ON do not start.Engine OFF dash board lights ON.
2. Press and release the reset button in the driver information center (DIC) until the OIL LIFE message is displayed.
3. Once the alternating OIL LIFE and RESET messages appear on the DIC display, press and hold the reset stem until several beeps sound. This confirms the OIL LIFE system has been reset.
4. Turn the key to lock. If the CHANGE OIL message comes back on when you start the engine, the ENGINE OIL LIFE system has not reset. Repeat the procedure
Alternate Method
1. Turn the ignition key to ON with the engine off.
2. Fully press and release the accelerator pedal 3 times within 5 seconds. Several beeps sound. This confirms the oil life system has been reset.
3. Turn the ignition key OFF.
4. If the CHANGE/OIL message comes back on when you start the engine, the engine oil life system has not reset. Repeat the procedure
I use the second method, it is more universal and it works for Chevy Venture too.

Nov 06, 2010 | 2003 GMC Sierra

2 Answers

Reset oil change light 2000 chevy venture


Try turning the key to the on position without starting the vehicle and press your gas pedal all the way to the floor 3 times within 10 seconds of turning the key to the on postion. If this doesn't work let me know and I'll have another solution.

Apr 20, 2010 | 2000 Chevrolet Venture

1 Answer

How do i reset change engine oil light on a 2000 chevy venture


1. With the ignition key in RUN but the engine off, fully push and release the accelerator pedal slowly three times within five seconds.

2. Turn the key to off.

IF the CHANGE ENGINE OIL light comes back on, the engine life monitor has not reset. Repeat the procedure.

I have noticed personally that I have press my accelerator 5 times. Each vehicle has it's own idiocyncracies

Sep 26, 2009 | 2000 Chevrolet Venture

1 Answer

How to reset the change oil light on a 2003 chevy silverado


Information courtesy of synthetic-direct.ca
Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
Best of luck.
Greg

Jul 15, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

How do i reset change engine oil 2000 model chevrolet venture


. With the ignition key in RUN but the engine off, repeatedly push the trip/reset button until OIL is displayed on the Driver Information Center. 2. When OIL is displayed, push and hold the trip/reset button for five seconds. The number will disappear and be replaced by 100 (indicating 100% oil life remaining). 3. Turn the key to OFF. If the change engine oil message comes back on, the engine oil life monitor has not reset. Repeat the procedure

Jul 11, 2009 | 2000 Chevrolet Venture

3 Answers

2000 Chevy Venture Fuel Pressure Regulator


use the pressure test port on the top of the engine, it is on the fuel rail that supplies fuel to the injectors, looks like a tire valve, will have a plastic cap on it.

Mar 22, 2009 | 2000 Chevrolet Venture

2 Answers

Oil light


If the oil light is on it's one of 2 things: You have no oil pressure, or the sending unit (also known as the oil pressure switch) is defective and is reading no pressure when there actually is normal pressure. You should always assume it means no pressure, because driving it this way will ruin the engine.

Mar 19, 2009 | 2000 Chevrolet Venture

1 Answer

Program master key for 2000 chevy venture


To program a new key...
1-Turn ON the ignition, with the engine OFF, using a master Pass-Key III key (black).

2-Observe the security telltale. After approximately 10 minutes the telltale will turn off.

3-Turn OFF the ignition, and wait 5 seconds.

4-Repeat step 1-3 two more times, for a total of 3 cycles or 30 minutes.
Tech JK
-----------------------------------------------

Jan 01, 2009 | 2000 Chevrolet Venture

Not finding what you are looking for?
2000 Chevrolet Venture Logo

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...