Question about 2006 Pontiac G6

1 Answer

My 2006 pontiac G6 keyless remote has about a 15 second delay before it will unlock the door, it wasn't always like this.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Pontiac Master
  • 540 Answers

I would try first replacing the battery in the remote

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Programming 2006 pontiac pursuit fob


Gm and Chevy fob can be programmed at home. I have done it my self for a 01 chevy a 03 sunfire.
The steps on
 Step 1 of 5
Get in your Pontiac G6 and make sure all the doors and the trunk are closed.

 Step 2 of 5
Put your key in the ignition and hold the "Lock" button on the driver's car door.

 Step 3 of 5
Turn the G6 key in your ignition from "On" to "Off" while holding the "Lock" button, and do two more cycles of "On" and "Off" in quick succession.

 Step 4 of 5
Release the "Lock" switch on your door and press and hold the "Lock" button on your keyless remote for 10 to 15 seconds.

 Step 5 of 5
Remove the key from the ignition of your G6, and test the programming.

Or

Or

 Step 1 of 9
Enter your vehicle and close all of the doors behind you besides the driver's door. Be sure to have your keyless remote and ignition key in hand.

 Step 2 of 9
Insert and remove the key from the ignition twice in a row and then close and open the door twice in a row.

 Step 3 of 9
Insert and remove the key from the ignition again and close and open the driver's door two more times.

 Step 4 of 9
Insert the key into the ignition and close the driver's door.

 Step 5 of 9
Cycle the key in the ignition "On" and then "Off" and then remove the key from the ignition.

 Step 6 of 9
Wait for the locks to cycle to indicate the beginning of the programming sequence.

 Step 7 of 9
Press and hold the unlock and lock buttons on your remote for two seconds and then release.

 Step 8 of 9
Press and hold just the
lock button on the remote for three seconds and wait for the locks to cycle to indicate successful programming.

 Step 9 of 9
Repeat steps seven and eight to program any additional remotes and open the driver's door to end the programming sequence once you are finished.
Hope this helps

Feb 04, 2012 | Cars & Trucks

3 Answers

Keyless remote issues 06 g6


FWIW,
I've had a similar problem, but ONLY using the remote to "Unlock" the doors (that's the only button I use on the remote). I found the special coating on the "Unlock" button that makes contact with the circuit board was wearing off. I got another fob from a friend, it worked for about a year and then the same problem. The semi-conductive coating was worn off as well.
I played around and was able to open the doors by touching the circuit board itself with my finger.
If that describes your problem search the web for replacement rubber buttons, it takes less than a minute to swap-out, they range from $700 to $10 plus shipping.
Also your fob shouldn't have needed re-programming, the dealers are making a fortune with this re-program ****.

For the technical types;
The coating is a semi-conductive coating. The resistance of a "good" pad was hard to measure. I put resistors across the circuit board, I started @ 10k, it worked, then 100k, 100k didn't work, 82k worked fine. I just added a small micro-switch and no problems since.

Good Luck

Jun 05, 2010 | 2006 Pontiac G6

1 Answer

2006 pontiac g6 keyless remote programming


must take FOBs to dealer for programming.... there is no other way and it's cheap (you can take any number of FOBs and it's still a flat rate (~$40)

May 20, 2010 | 2006 Pontiac G6

1 Answer

How can i start my car without Remote keyless entry?


Use the driver's door key cylinder> Lock and unlock the car with the key after all doors are closed and this should solve the problem. If not, then it has nothing to do with the RKE Transmitter.

May 03, 2010 | 2006 Pontiac G6

1 Answer

How do I change the battery on keyless remote


the keyless remote splits in half then just remove the battery and replace, i have an 07 and thats what i had to do

Mar 15, 2010 | 2006 Pontiac G6

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Remote start


first make sure you have the keyless start entry setup. if u do then you need to lock the door with the transmitter after you lock the door press the start button and hold it down until it starts. It usually takes three or four seconds.

Mar 16, 2009 | 2005 Pontiac G6

1 Answer

Keyless remote


Don't know for sure it will work with your but try this.

  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the door unlock switch.
  4. While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation.

Sep 25, 2008 | 2006 Pontiac G6

Not finding what you are looking for?
2006 Pontiac G6 Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...