Question about 1997 Ford Contour

Open Question

I need location for ford contour ecm computer modle or pcm

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 225 Answers

SOURCE: Where is the Ford Contour computer located?

behind the glove box i dont know the exact spot but its locaed behind the glove box that i do know

Posted on Nov 03, 2009

Testimonial: "Thank you. Our mechanic could not find it!!"

Ad
outdoorsman5
  • 631 Answers

SOURCE: Help 95 ford contour obd-1 error 335

I was reading in one of my repair manuals and it says in there that there could be a block where the exhaust gas pressure sensor is. There could be a blocked inlet hose. Or it could be the ECM.

Posted on Sep 11, 2009

emissionwiz
  • 76848 Answers

SOURCE: used pcm/ecm for a 2001 Ford Expedition

1st it must be the correct engineering number, not just the same year, but the exact same number on the sticker. then it must be programmed by the dealer

Posted on Nov 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CANNOT FIND THE KEYLESS ENTRY RECEIVER MODLE IN A 2000 FORD CONTOUR,THE PERSON THAT SENT THE VIDEO WAS OF THE WRONG CAR....CAN SOMEONE PLEASE HELP......THANKS...


It's actually called Anti-theft / Central locking module . And it is located under the dash or in the trunk . Heres a picture so you know what it looks like . On these older vehicles you just need to do a little digging to find parts ,


1383_1-mqwzpxjajnvmm0dxfose2z4g-2-0.jpg

Feb 15, 2017 | Ford Cars & Trucks

1 Answer

How do I adjust idle speed?


You can't adjust the idle , There is a minimum idle adjustment set at the factory , you don't want to mess with that . The PCM / ECM ,engine computer controls the idle speed by the idle air control valve (motor) . You may have a dirty throttle plate mess with the base idle .Check out this video on ford base idle adjustment . Some one who didn't know cranked up the base idle causing problems Ford IAC valve test how to adjust minimum idle speed

Dec 19, 2015 | 1996 Ford Contour

1 Answer

Can someone please tell me where to hook up a timing lite on my 1999 ford contour


The timing on Contours is not adjustable, as it is controlled by the Engine Control Module (ECM), the computer that controls and monitors the engine functions.

Aug 06, 2013 | Ford Contour Cars & Trucks

1 Answer

98 contour repair manual


You don't need a repair manual if you know the basic's of automotive repair . You just need wiring diagrams an fuse box layouts . You can find those here free http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model ,engine ! Under system click on electrical distribution .Then under subsystem click on fuse panel . Click the search button then the first blue link . This shows relay positions in the under hood fuse box. The PCM power relay supply's B+ voltage to the fuel pump relay , PCM - engine computer ,mass air flow sensor an someother thing's .

Jul 18, 2017 | 1998 Ford Contour

1 Answer

How do i replace the ECM on a 1999 ford contour with a 2.0L engine


the PCM is behind the passengers kick panel, but i recomend taking it to a ford dealer to have it installed, because it needs to be programed with a ford diagnostic computer.

Feb 18, 2012 | Ford Contour Cars & Trucks

2 Answers

What causes a p 0327 diagnostic code on a 95 contour


P0327 - Knock Sensor 1 Circuit Low Input Bank 1 or Single Sensor
First check the knock sensor connector. If the connector is clean and secure, replacing the knock sensor usually takes care of the problem.

- An excessively low voltage from the sensor is sent to Powertrain Control Module (ECM) or Engine Control Module (ECM)

The knock sensor is attached to the cylinder block. It senses engine knocking using a piezoelectric element. A knocking vibration from the cylinder block is sensed as vibrational pressure. This pressure is converted into a voltage signal and sent to the Powertrain Control Module (PCM) or Engine Control Module (ECM).

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power

Possible causes
- Knock sensor circuit short to GND.
- Knock sensor circuit short to PWR.
- Knock sensor circuit open.
- Damaged knock sensor.
- Faulty Powertrain Control Module (PCM) or Engine Control Module (ECM).


Test and check it. Hope helps.

May 12, 2011 | 1995 Ford Contour

1 Answer

Location of ecu on a 2005 ford freestyle


Keep in mind the definitions:
* ECM = Electronic Control Module (prior 1995 computer, OBD1)
* PCM = Powertrain Control Module (1995 and newer, OBD2)


Ford Freestyle 2005 - Powertrain Control Module The PCM is located in the ine compartment, passenger side, mounted to the cowl. Removal & Installation procedure:
  1. Retrieve the module configuration.
  2. Remove the cowl panel grille.
  3. Disconnect the 3 PCM electrical connectors.
  4. Remove the bolt and the PCM.
To install:
  1. Installation is the reverse of removal.

4f23c78.gif

Hope helps (rememnber rated this).

Jul 14, 2010 | 2005 Ford Freestyle

1 Answer

Help 95 ford contour obd-1 error 335


I was reading in one of my repair manuals and it says in there that there could be a block where the exhaust gas pressure sensor is. There could be a blocked inlet hose. Or it could be the ECM.

Sep 10, 2009 | 1995 Ford Contour

1 Answer

Check engine light stays on


hi. i recommend taking this car in for a diagnostic scan run on the ecm/pcm. there is a serious issue concerning one or more of the vital sensors on this engine.

May 21, 2009 | 1998 Ford Contour

1 Answer

Where is the ignition module located on the 1996 ford contour?


tragik nc: In looking this car up in both the 4 and 6 cyl configurations, Ford said that the ignition control module is no longer a separate component. It is actually integrated into the PCM (power control module)
This is located in the right rear corner of the engine compartment behind the power steering reservoir.
Good Luck, mybunkey>>>>>>>>>>>>>>>>>

Apr 20, 2009 | 1996 Ford Contour

Not finding what you are looking for?
1997 Ford Contour Logo

Related Topics:

373 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...