Question about 1994 Ford Aspire

Open Question

Must I drop fuel tank to install fuel pump on 94 aspire?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
bradk99
  • 2 Answers

SOURCE: Fuel Pump - 2000 Ford Mustang

the best place to get any answer for a mustang is here: and I hope I don't get booted off this site for it - but it really has any answer you're looking for - 3.8mustang.com

Posted on Jun 16, 2008

Ad
  • 1 Answer

SOURCE: fuel pump removal?? drop the tank?????

See if access can be through trunk..I"ve cut a square hole above pump in trunk floor on other makes works fine..I've got electric sheet metal shears,,looks like drill..but CAREFULLY use air chisel too

Posted on Feb 23, 2009

  • 1 Answer

SOURCE: 2001 ford focus fuel pump

Yes you do. Be careful of the plastic fuel supply line when you reinstall the assembly. The hose can kink, and you will not have fuel pressure.

Posted on Mar 25, 2009

  • 6982 Answers

SOURCE: 99 Crown Victoria fuel pump replacement

Use lots of wd40 on tank strap bolts. If they bigin to bind tighten them up and losen again to get rust out of threads. If you remove the straps, why not remove the fill neck and lower tank? Much easier to work that way!!!

Posted on Apr 03, 2009

  • 4369 Answers

SOURCE: i am not getting fuel to my engine

Removal

  1. Relieve the Fuel System Pressure . Refer to the procedure in this section.
Cushion Cover and Pad, Rear Seat — One-Piece and 50/50 Split Fold Removal
  1. Remove the two rear seat cushion bolts.
  1. Fold the rear seat back cover and cushion (60084) forward.
  1. Carefully pull the rear seat cushion and cover (60030) out from under the rear seat back cover and cushion and remove the rear seat cushion and cover from the vehicle
  1. Remove the rear seat cushion and cover (60030). Refer to Section 01-10 for the removal procedure.
  1. Remove the three luggage compartment floor cover hold-down pins and fold the luggage compartment floor cover (45455) forward until the fuel pump assembly access plate is visible.
  1. Remove the four fuel pump assembly access plate screws, the ground lead, and the fuel pump assembly access plate from the chassis.




  1. Disconnect the fuel pump assembly electrical connector.




  1. On 4-door vehicles, remove the fuel vapor tube shutoff valve bolt and the evaporative emission tube shut off valve (9G332) from the bracket on the fuel pump assembly housing.




  1. Loosen the two hose clamps and disconnect the two fuel pump hoses from the fuel pump hose fittings on the fuel pump assembly housing.




  1. Remove the four screws (2-door) or eight screws (4-door) and lift the fuel pump assembly housing from the fuel tank (9002).




  1. Disconnect the fuel level sensor electrical connector.
  1. Remove the two fuel level sensor washers and fuel level sensor nuts and the fuel level sensor.



-------------------------------------------------------------------------------------
Section 10-01: Fuel Tank, Filters, Lines and Electric Fuel Pump 1996 Aspire Workshop Manual
REMOVAL AND INSTALLATION Fuel Pump Removal
  1. Remove the fuel level sensor. Refer to the Fuel Level Sensor removal procedure in this section.
  1. Remove the fuel pump screw, fuel pump grommet and the fuel pump bracket from the bottom of the fuel pump (9350).




  1. Remove the fuel tank sender filter bracket, fuel tank sender filter (9A011) and the fuel tank sender filter retainer from the fuel pump.
  1. Disconnect the fuel pump electrical connector.
  1. Remove the clamp and the fuel pump from the fuel pump assembly housing.

Posted on Apr 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel pump located on a 1994 accord?


I'm almost certain it is inside the gas tank.In 94 the pumps were electric.

Jul 06, 2014 | 1991 Honda Accord

1 Answer

I have a 94 Dodge Ram 1500 4x4 5.9L With a bad fuel pump. What I would like to know is how to release the fuel pressure in the line before removing the fuel pump. Also do I have to drop the fuel tank to...


Well I released my pressure by pushing in the valve near the injectors under the hood. Make sure your engine is cold when doing this. Only a quick spray then its relieved. I unbolted my bed and jacked it about 5 inches and was able to change my 94 ram fuel pump. Pretty easy this way as those straps may need to be eplaced if removed. I did this 2 years ago. Maybe to an hour or 2. But if your truck has been sitting yow may want to drop the tank to clean it out.

May 01, 2013 | 1994 Dodge Ram

3 Answers

Do I have to drop the fuel tank to replace the fuel pump on a 94 Buick le saber


Yes ,,instructions are below, Use eye protection for this procedure
Remove or Disconnect:

  1. Relieve Fuel Pressure
  2. Disconnect negative battery cable
  3. Raise vehicle on hoist
  4. Remove Fuel Tank
  5. Remove Fuel Gage sending and pump assembly by turning cam lock ring counterclockwise. Lift assembly from fuel tank and remove fuel pump from fuel gage sender unit.
  6. Disconnect pump wires, hose clamps, and clamp around pump body
  7. Pull pump assembly out of rubber connectors
  8. Inspect fuel pump attaching hose for any signs of deterioration. Replace as necessary.
Install or Connect:

  1. Push fuel pump assembly into attaching hose
  2. Connect pump wires, hose clamps at attaching hose and around pump body
  3. Place Fuel tank sending unit and pump assembly into tank using new O-ring
  4. Place cam lock over assembly and lock by turning clockwise
  5. Install Fuel Tank
  6. Start engine and check fuel pipe connector for visual leaks

Oct 20, 2010 | 1994 Buick LeSabre

2 Answers

Gas leaken new tank 94 4 runner think its fuel pump seal but dont wanna drop tank if dont have to found axcess pannel under rear passenger seat but dont see fuel pump to see if thats where its leaking from...


If the smell is coming from the back of the vehicle then it could be leaking from the return line or the filler hose. I would check the fuel filler hose first since you can probably get at it wihtout dropping the tank. You might be able to get to the return line as well which is a small hose that goes to the tank from the fuel pressure regulator to return unused fuel. If the smell is coming from the front of the vehicle I would inspect all of the fuel lines and the inline fuel filter if you have one installed and verify that none of the hose is damaged and all clamps are tight. Check your injector rail and make sure it is not leaking where it provided fuel to the injectos and check your injectors seat to see if there is any evidence of fuel leakage.

If you can't find any leaks in those locations then you are gonna have to drop the tank and check the pump.

Apr 08, 2010 | 1994 Toyota 4Runner

3 Answers

Is there a door to get to the fuel pump in the trunk of a 94 cavalier


NO THE FUEL TANK MUST BE REMOVED, ONLY A FEW CARS HAVE AN ACCESS PANEL AND MOST OF THOSE ARE FORIEGN MODELS.

Mar 27, 2010 | 1994 Chevrolet Cavalier

1 Answer

Install a gas tank in a 94 toyota corolla


Raise the car.

Loosen the fuel filler neck rubber hose clamp. Remove hose from tank. Insert tubing into tank and siphon out all fuel.

Undo the brake line bracket blots and move brake lines out of the way.

Undo the exhaust to muffler flange bolts. Exercise extra care if they appear rusted as they will shear off.

Remove rear seat and undo fuel pump cover. Undo fuel pump bolts.
'
Disconnect the fuel and return lines.

Support tank with a jack. Undo tank strap bolts. Remove straps.

Lower tank and remove fuel pump.

Drop tank and slide out over exhaust.





Nov 02, 2009 | 1994 Toyota Corolla

3 Answers

How hard is it to replace fuel pump on 1996 oldmobile bravada


fuel tank needs to be empty, remove fuel tank, replace pump and sending unit

Oct 10, 2009 | 1996 Oldsmobile Bravada

1 Answer

94 Grand Am looses power and abuses fuel. What is


Your fuel filter is probably on the fuel pump or on the fire wall of your engine - Mostly likely off of your fire wall. If it is loosing power have your catalytic convertor checked. Change your fuel pump, this could be your problem. All of these you can change yourself. I don't believe that a '94 Grand AM has an access panel to the fuel pump so you will have to drop the tank - Just make sure that it is below a 1/2 tank before dropping it. Buy a Chilton and it will give you step by step direction. Good luck!

May 16, 2009 | 1994 Pontiac Grand Am

2 Answers

I am not getting fuel to my engine


Removal
  1. Relieve the Fuel System Pressure . Refer to the procedure in this section.
Cushion Cover and Pad, Rear Seat — One-Piece and 50/50 Split Fold Removal
  1. Remove the two rear seat cushion bolts.
  1. Fold the rear seat back cover and cushion (60084) forward.
  1. Carefully pull the rear seat cushion and cover (60030) out from under the rear seat back cover and cushion and remove the rear seat cushion and cover from the vehicle
  1. Remove the rear seat cushion and cover (60030). Refer to Section 01-10 for the removal procedure.
  1. Remove the three luggage compartment floor cover hold-down pins and fold the luggage compartment floor cover (45455) forward until the fuel pump assembly access plate is visible.
  1. Remove the four fuel pump assembly access plate screws, the ground lead, and the fuel pump assembly access plate from the chassis.




  1. Disconnect the fuel pump assembly electrical connector.




  1. On 4-door vehicles, remove the fuel vapor tube shutoff valve bolt and the evaporative emission tube shut off valve (9G332) from the bracket on the fuel pump assembly housing.




  1. Loosen the two hose clamps and disconnect the two fuel pump hoses from the fuel pump hose fittings on the fuel pump assembly housing.




  1. Remove the four screws (2-door) or eight screws (4-door) and lift the fuel pump assembly housing from the fuel tank (9002).




  1. Disconnect the fuel level sensor electrical connector.
  1. Remove the two fuel level sensor washers and fuel level sensor nuts and the fuel level sensor.



-------------------------------------------------------------------------------------
Section 10-01: Fuel Tank, Filters, Lines and Electric Fuel Pump 1996 Aspire Workshop Manual
REMOVAL AND INSTALLATION Fuel Pump Removal
  1. Remove the fuel level sensor. Refer to the Fuel Level Sensor removal procedure in this section.
  1. Remove the fuel pump screw, fuel pump grommet and the fuel pump bracket from the bottom of the fuel pump (9350).




  1. Remove the fuel tank sender filter bracket, fuel tank sender filter (9A011) and the fuel tank sender filter retainer from the fuel pump.
  1. Disconnect the fuel pump electrical connector.
  1. Remove the clamp and the fuel pump from the fuel pump assembly housing.

Apr 19, 2009 | 1995 Ford Aspire

Not finding what you are looking for?
1994 Ford Aspire Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...