Question about 1991 Nissan Maxima

1 Answer

How to remove transmission of a 1991 nissan maxima. i want to know if passenger side axel has to be removed

Posted by on

Ad

1 Answer

You pull both axles first,then the transaxle on all front wheel drive vehicles.

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 Nissan maxima wont go forward


you have a transmission problem your forward clutches may have to change,did you check the shift cable by the neutral switch if all those area check ok the transmission have to be repaired

Feb 25, 2015 | 1991 Nissan Maxima

1 Answer

What kind of hydraulic fluid do I put in my 1991 nissan maxima?


Hi Kelly,use dot 3 or 4 for your brakes and clutch reservoir,if you have a manual transmission.I use dot 3 on my Nissan .

Feb 25, 2013 | 1991 Nissan Maxima

1 Answer

Where is the computer located on a 1999 nissan maxima SE 3.1L?


its under the radio on the floor. look on the floor right next to the gas pedal. you will see a black side cover. remove the cover and you will see the computer. there is a cover on the passenger side also. right under the glove box next to your left foot if you were sitting in pass. side seat.

Sep 12, 2012 | 2001 Nissan Maxima

2 Answers

2001 mitsubishi eclipse gt spyder clutch removal. how do you get the axles out and how do you release the bearing for the tranmission to seperate


After the axel is removed from the outher wheel bearingf( seaparate the steering knuckle from the lower ball joint) and pull the axel out of the bearing after the axel nut has been removed then the axel will pry ou tof the transmission.. Might take a strong pry witht he haelp of a hammer. the one side might have a carrier bearing on the CV axel that bolted to the back of the engine block. It'll have to be unbolted. too. the starter will have to be removed also as all the bolts that hold the engine to the transmission.

May 14, 2011 | Mitsubishi Eclipse Spyder Cars & Trucks

1 Answer

Where is vehicle speed sensor located on 01 maxima?


VEHICLE SPEED SENSOR SHOULD BE LOCATED ON THE TRANSMISSION! SOME HAVE A SPEEDOMETER CABLE ATTACHED TO THEM, AND SOME DON'T! ON FRONT WHEEL DRIVE, THEY ARE LOCATED ON THE PASSENGER SIDE NEXT TO THE FIREWALL ON TOP OF THE TRANSAXLE! YOU MAY HAVE TO REMOVE THE Y-PIPE TO THE EXHAUST, AND A HEAT SHIELD, TO GET TO IT!

Feb 19, 2011 | 2001 Nissan Maxima

2 Answers

1991 Nissan Maxima will only go several feet in Drive, then when engine and transmission warm, transmission no longer engages at all. Engine is running fine. Do I need to get transmission replaced or...


i have the same problem on the same year and i think its the filter but i cant find it there is no pan on the bottom and i have tried lookin every where and the guy at orileys said it was internal and i would have to take it to get it done but i can do it but i need to know where it is?

Aug 31, 2010 | 1991 Nissan Maxima

1 Answer

Tail lights broken on my 1998 Nissan Maxima GLE. Want go get new one for the passenger side and replace it.


Remove felt cover in trunk area around light, remove securing nuts and unplug the unit, assembly is reverse, ensure you install the seal with it. Good luck

Nov 20, 2009 | 1998 Nissan Maxima

2 Answers

Trying to replace headlight bulb in nissan maxima


It depends on which side you are talking about. I took out the airfilter to get to the driver side and I went throught the wheel well on the passenger side. Some of my friends took off the entire front bumper for easier access. Either way you'll save $$$ from having them installed at a dealer.

Jul 09, 2009 | 2004 Nissan Maxima

2 Answers

1991 nissan maxima


I just went thru this on mine... it is easiest to get to from the bottom right corner... remove the shields and it's right there... take the lower adjustment bolt out , the upper rear bolt and the upper outer bolt out , drop it down and swap wires and replace . Tip; a shorty phillips screw driver works well to allign the holes on the upper rear bolt. DO NOT tighten any of the bolts untill they are all in.

Jul 21, 2008 | 1991 Nissan Maxima

Not finding what you are looking for?
1991 Nissan Maxima Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...