Question about 2005 Dodge Stratus

1 Answer

I need a print out showing where the camshaft sensor is at on a dodge 2005 stratus

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 56 Answers

Go to a search engine and enter Dodge Forum,go there and you can find what you need!

Posted on Aug 05, 2010

  • shayla582 Aug 05, 2010

    thanks i will go there now.. do i go to google first.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Diagram of where a camshaft sensor is on a dodge stratus 2.4L 4 cylinder

2003 model
not confirmed
crank angle sensor might be near the stater motor on the block



Jul 07, 2016 | Dodge Cars & Trucks

1 Answer

Where is the camshaft sensor located on a 2005 Dodge Stratus 2.4L

on the end of the cylinder head toward the drivers side of the car. it runs off the front or intake camshaft. right where the valve cover . meets the head. its kind of round and is held on by two bolts. its easy to change

Oct 04, 2014 | 2005 Dodge Stratus

1 Answer

2005 dodge stratus SXT 2.4l DOHC died in traffic and won't start

Did you check your camshaft position sensor circuits to see if they were working correctly or test the sensor itself before going out and replacing the sensor?....Didn't think so....

Lesson learned here? Diagnostic Test Codes (DTCs) DO NOT tell you what parts to replace. They only tell you which systems or circuits in your vehicle are not working as they should be. Then it is up to the person diagnosing the car to determine what is actually CAUSING the system or circuit to malfunction......Of coarse, this requires that you must first understand how the system is supposed to work...

Anyway, with some proper diagnosis, I think you will probably find that your cam sensor code (P0340) is being caused by a broken timing belt.
(If the cam does not turn, the cam sensor does not produce a signal, and the computer has a problem with that).

May 26, 2012 | 2005 Dodge Stratus

1 Answer

After having my 06 dodge stratus checked out. 6 codes showed up. I don't want to just start throwing parts on without knowing the real reason for the problem. The car drives fine and then just...

Let's start with the codes.

Po129 refers to barosensor

Po344 is a code for the camshaft position sensor

Po339 crankshaft position sensor

Po340 camshaft position circuit malfunction

Po335 crankshaft POS sensor malfunction

Po122 throttle pedal position

Item 2,3,4,5 relate to each other that s camshaft and crankshaft position sensors. Since both already show a malfunction code, it would be advisable to change.

Sometimes other codes show up because there is a relation but not that the item is bad.

Jan 19, 2018 | 2002 Dodge Stratus

1 Answer

How many crankshaft sensor are on a 2005 dodge stratus 2.4l dohc

usually only one crankshaft sensor and one camshaft sensor on every engine for starting.

May 01, 2011 | 2005 Dodge Stratus

4 Answers

Where is the camshaft position sensor located on a 2004 dodge stratus 4 cyl 2.4L engine

the camshaft sensor is mounted on the camshaft housing located on the end of the cylinder head.

Jul 08, 2009 | 2004 Dodge Stratus

1 Answer

I have a 2005 Dodge Stratus with a bad camshaft position sensor. Are they easy to replace or will I need to have it done?

For a 2.7 liter six cylinder engine, the camshaft position sensor is located in the front or on the right side of the front engine head. Be sure the engine is cool before you start to remove it. It's fairly easy to change, just in an awkward spot to get to. You can see the connector on the front of the head just right under the top radiator hose. The sensor is held in with a 13mm bolt that has a wiring support tab attached to the top. Remove the wire support tab and then remove the bolt. After the bolt is out, just pull the sensor out with you fingers. A new sensor from the dealer will run around $55.00.  Good luck and hope this helps. keep me posted, be glad to help.

Jun 22, 2009 | 2005 Dodge Stratus

1 Answer

Where is the camshaft position sensor located?

its on the bottom of the engine block, there is a heat shield covering it, thats why you can't find it, its around the intake manifold

Dec 06, 2008 | 2005 Dodge Stratus

Not finding what you are looking for?
2005 Dodge Stratus Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides