Question about 1996 Honda Accord

Open Question

1990 mazda miata mx-5 how to bleed clutch slave cylinder

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

Ad
  • 1056 Answers

SOURCE: replaced clutch slave cylinder blew

Could be a couple of different things.
1) your clutch master has a plugged pressure bypass, and it is sending excessive pressure to the slave and blowing it out.
2) The clutch throw out arm is bound, and will not allow the slave to compress it.
3) The replacement slave was defective.

What was the reason for replacing the slave in the first place?

Posted on Jul 31, 2008

  • 275 Answers

SOURCE: Bleeding clutch slave cylinder

if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Posted on Nov 12, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

  • 1 Answer

SOURCE: 95 mazda b4000 slave cylinder bleeder valve location

the nipple sticks out side the bell housing on the left side just above your hydralic line for your clutch,auto zones web has a complete diagraham and steps for bleeding

Posted on May 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to bleed the air out of my clutch on a 96 Maita. where is the nipple on the slave cylinder?


If not obvious, slightly loosen supply line. Remember, air rises, so bleed at master also.

Jul 06, 2015 | 1996 Mazda MX-5 Miata

1 Answer

Bleed clutch lines on 99 miata manual clutch


Underneath the vehicle there is a clutch slave cylinder that has a bleed port.
bleeding clutch for slave cylinder replacement

Feb 07, 2015 | 1999 Mazda MX-5 Miata

1 Answer

Bleed clutch


Almost always the slave that fails. Rebuild kits are cheap as it an entire new slave cylinder. Bleeding steps here How to Bleed Your Clutch Hydraulics Without Helper

Jan 02, 2014 | 1990 Mazda MX-5

1 Answer

Throw out bearing stuck in miata mx5


Hi, The throw out bearing should not have been affected with anything that you have described.
Quick note about bleeding: Bench bleed the master cylinder, then never let it run dry.
Anyways, you seem to have too many things happening at once. I worry about the clutch itself. When they wear, travels of things line throwout bearings become excessive.
If by stuck you mean beyond fully extended, certainly a clutch.
If by stuck you mean it is released and will not engage, maybe not a clutch...Make sense?
Essentially, you need the clutch to work correctly, sometimes you just gotta rip it apart and redo it.

Dec 12, 2012 | 1996 Mazda MX-5 Miata

1 Answer

Clutch piston too short?


sounds more like a seal to me

Sep 16, 2012 | 1997 Mazda MX-5 Miata

1 Answer

Bleeding mx 5 mark 1 clutch


there is usually a bleeder screw right on the slave cylinder that ur clutch cable connects to at the transmission. as far as fluid, just look in your manual or google it

Mar 24, 2012 | 1993 Mazda MX-5

1 Answer

Alright, I have a 1991 Mazda MX-5 Miata. I've recently had a lot of difficult shifting into gears while driving. I have to pump the clutch a few times before being able to get into gear. It's definitely...


You bleed the brakes afterward. If you but a Hayne's Manual for your specific car, it will give you detailed instructions on how to change them. It will show step by step procedures. Also, if you ask an expert, they can give you step by step procedures until the job is done properly. Sorry I couldn't help more.

Feb 05, 2011 | 1991 Mazda MX-5

2 Answers

Shifter works when car is off, start car and then shifter won't go in gear. if i start vehicle in first with clutch pedal to floor, car starts going forward. mazda miata mx-5 just put new slave cylinder in...


The one item I would suspect is the through-out-bearing not completely disengaging the pressure plate from the fly wheel. If the vehicle is in neutral and you slowly depress the clutch and release it do hear a singing or whining sound? Since you cannot adjust the clutch any more the through-out-bearing is the component which moves the pressure plate from the fly wheel to stop the power from the engine to the transmission. It is difficult to shift when the engine is on because the fly wheel is still engaged and powering your transmission.

Aug 06, 2010 | 1997 Mazda MX-5 Miata

2 Answers

Clutch is engaging more quickly than usual. Engages almost immediately when raised from floor. Pedal feels softer than normal.


Yes you are correct its to much free travel to start with as it sounds like you have to get the master or slave cylinder rebuilt with new rubber kit as its either loosing pressure going down or air getting in as you put pressure on it.
So take off the slave and master cylinders and have then honed out and new kits replaced and you should
be ok to bleed and drive ..

Oct 08, 2009 | 2000 Mazda MX-5 Miata

1 Answer

Car shifts when not running, however once started gears won't shift....


Clutch isn't being released when pedel is pressed in. you need to either bleed the clutch, or adjust the clutch.You may have a pitted slave cylender. this means that fluid is passing around the piston in the slave cylender. if so you need to rebuild or replace the slave cylender. there may be other reasons too but these are some of the most common reasons

Apr 22, 2009 | 1997 Mazda MX-5 Miata

Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

621 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...