Question about 2002 GMC Safari

1 Answer

How to remove linkage for shift cable to trans

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 11,800 Answers

Please be more precise. If by that you are asking how to disconnect the linkage from the tranny then all you have to do is to unscrew the bolt with an open ended wrench.

Posted on Aug 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix the linkage on the transmission on 2001 Lincoln navigator


First thing is to get safety glasses,block wheels securely !!...set emergency brake..,get a good flashlight.Disconnect negative battery cable...Some can wear inside the steering column,some can be a worn linkage cable ...The lever on the transmission located under vehicle Trans at lower part of trans,driver side can become loose or possibly damaged...First get under vehicle with safety glasses and observe operation of the lever where shift cable is mounted while assistant puts it in park...make sure the trans shift lever mounting nut is tight before shifting..If assistant can't get it in park use your hand and push forward on the linkage arm and it should go into park manually...If this is the problem you need to change shift cable...Some wear inside the column where steering wheel is mounted..If cab shifter feels very loose ..You will have to remove steering wheel and column cover to inspect."..The cable runs from trans to the steering column..Look between gas and brake pedal and verify cable coming up through floor board and runs to steering column...Double check shifter lever at trans is tight because it is mounted on a splined stud and it can strip the stud threads if it becomes loose..If loose remove lever and inspect splines for damage..Call dealer and make sure they have the part..Remove old cable from trans and put it in park with your hand...Remove and replace cable..Be sure lever inside cab and lever on the trans are both fully engaged into park while cable is removed before installing new cable....Attach new cable.....

Oct 16, 2014 | 2001 Lincoln Navigator

1 Answer

Stick shift hard to get into first. How fix?


First check the linkage

Then loosen or disconnect to linkage,
so you can shift the trans by hand

If it has a cable involved, remove the trans end

My guess is-- you need to pull the trans & take it
apart to find the worn parts & problem

Also the clutch may be an issue

Jul 04, 2014 | 2003 Ford Ranger Regular Cab

3 Answers

Automatic gear shift in 94 toyota tercel stuck


what is stuck?

the linkage or the cable from the shifter to the trans.?

block the tires so the car can not roll away...
open the hood and remove the cable from the shifter on the transmission.
see if you can manualy move the shifter on the trans.
if that moves... you may need to replace the cable (shift linkage)

Feb 19, 2011 | 1994 Toyota Tercel

1 Answer

How do i find the lenght for a 1996 chevy shift cable


That does not have a shift cable. It has manual steel linkage located under the hood, By the firewall on steering column, It runs down to trans linkage, Very accesable to do, Make sure you block both sides of tires well and use ebrake, If you move the linkage on the trans its free to roll...

Jun 18, 2010 | 1996 Chevrolet K1500

1 Answer

TRANS. WONT SHIFT. The shifter moves but the car doesn't move. Just a quiet clicking.


check the trans shift cable and linkage for damage or disconnected sometimes the linkage disconnects from the transmission linkage

Nov 30, 2009 | Chevrolet Lumina Cars & Trucks

1 Answer

Trans wont shift in to OD.


Check linkage at tranny, the new car use a cable to shift, Sometimes the cable slips within cover due to break in cover or cover ends. remove cable at tranny and shift by hand.Replace cable and see if it has the same amount of travel.

Oct 15, 2009 | 1999 Dodge Ram

1 Answer

My 03'Pontiac Montana quit shifting. The arm moves freely but nothing happens. I was told by a friend that a coupler connected to my shift arm was broken. how do I fix this coupler?


sounds like you need a new shift cable most likely- can you hear like a rachet noise when shifting if not proberly cable you need two people one in car shifting linkage with car off the other looking at trans linkage below brake master cylinder to see if linkage moves if linkage moves you have internal trans problem

Oct 10, 2009 | Pontiac Montana Cars & Trucks

2 Answers

Shifter won't shift gears


Have someone look @ linkage on trans. while someone moves shift lever thru the gears. If lever @ trans doesn't move then its in the linkage between the column and trans. (possible clip or pin broken @ linkage jounts). If lever @ trans moves then its a trans. internal prob.

May 03, 2009 | Ford F-150 Cars & Trucks

1 Answer

Plastic sleeve on shift linkage cable is broken


You cannot take the sleeve off. It comes with a new cable. Shift cable is enough for any parts man to know what you need. Generally this item is a dealer part.

Mar 26, 2009 | 1996 Chevrolet C1500

1 Answer

1999 ram auto trans wont shift into park


you could need a throttle linkage adjustment. first check to see if your ram will start in "park" and "neutral" only. if it starts in any other gear=faulty neutral safety switch. replace. ok, now check linkage for proper adjustment...with engine off and in park...remove intake housing..disconnect cableend from attatchment stud on your throttle body..slide cable off the stud (carefully)..verify that the transmissionthrottle lever is fully forward (idle) position..and verify that the lever on the throttle body is at curb idle pos..insert small screwdriver under edge of the retaining clip and remove..center the cable end on attatchment stud to within 0.04", or 1mm. install retaining clip onto cable housing..check cable adjustment..be sure trans throttle lever and throttlr body lever move in sync with each other.

Jan 11, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
2002 GMC Safari Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...