Question about 1991 Chevrolet Astro Extended

1 Answer

Passenger side turn signal both front and rear are out, but fuse is still intact. what would I check first?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 48 Answers

FIrst, check the bulbs then the flasher

Posted on Aug 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My left turn signal for my Honda Civic 2007 doesn’t work, the fuses and rally work perfectly, what should I do?


1. Pressed the hazard switch. Right side OK, but no left turn signal or lights.

2. Checked the tail turn signal by swapping passenger and driver bulbs. (bulbs twist out). At least the rear bulbs were OK. The wiring seemed intact, with no water leaks, etc.

3. Tested the circuit by removing flasher relay. Inserted a jumper wire between the 2 and 6 locations (Thanks to the message in this thread). The front, rear and dash turn lights all checked OK.

4. Replaced the relay - Honda part 38300-SDB-A03. $23 bucks at local dealer.

5. YAHOO - it worked.

Feb 04, 2018 | Honda Cars & Trucks

1 Answer

2011 Chevy Silvarado 1500 LS turn signal lights on the front passenger side don't work and rear goes fast...


Circuit/System Description
Ground is applied at all times at G201 to the turn signal/multifunction switch. The turn signal lamps may only be activated with the ignition switch in the ON or START position. When the turn signal/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is applied to the body control module (BCM) through either the right turn or left turn signal switch signal circuit. The BCM then applies a pulsating voltage to the front and rear turn signal lamps through their respective control circuits.
.
Did you check the RT STOP TRN fuse 15amp insturment panel fuse box.
Fuse Block - I/P
Left of the I/P behind the side trim panel
If the fuse is good , you could have a wiring problem or the BCM is bad .

Sep 08, 2017 | Cars & Trucks

1 Answer

Turn signals


Do you know how to do automotive electrical testing ? How to use a DVOM - digital volt ohm meter ? You have high resistance in the circuit . Use voltage drop to find the problem .
Mastering Voltage Drop Testing with Pete Meier and Jerry Truglia

Apr 14, 2017 | 1998 Buick Century

1 Answer

Turn signal won't work


Start by checking the light bulbs. They are accessible in the trunk for the rear and in the bumper for the front. If bulbs are intact, then check your fuse box. Remember that you have two fuse boxes, one in the vehicle usually on the driver side and can be accessed as you open the door. You have a second fuse box under the hood usually on the driver side. Most fuses are labeled. With a test light, you should be able to determine if fuses are good or not. Good luck and happy motoring.
Harold Villa

Apr 09, 2014 | 2003 Chevrolet Cavalier

1 Answer

What make the turn signal stop blinking


check the lamps inside the turn signal housings on the side of the vehicle your trying to indicate........ie passenger side front and rear or driver side front and rear.

Also is it only one side, or both? when turn indicator is operated?
check fuse block to see if fuse is blown. owners manual will show a fuse box location and identify which fuse if for turn indicators

Jan 27, 2013 | Cars & Trucks

1 Answer

Driver front turn signal does not blink. front


This may have more then one bulb in the front or possibly a bad socket try wiggling the new bulb in the socket to see if it will work.Compare all turn signal lights that come on the passenger side to those drivers side.Some vehicles also incorporate sidemarker lights with the turn signals.

May 29, 2010 | 2001 Pontiac Aztek

1 Answer

Driver side signals only work when headlights are OFF


What may have happened is either the headlights wiring or the parking lights wiring somewhere along the wiring fused to the left turn signals wiring. Depending on if the turn signals go on when you put the parking lights on or the headlights on.

If the signals come on when you turn on the headlights than you only need to locate the light green wire that comes off the left turn signal harness.

Next follow that wire the entire way back to the firewall looking for another wire fused to that wire as you go.

If there are no signs of this you need to continue looking on the other side of the firewall all the way back to the turn signal and hazard flasher unit which is a black box that connects to a black harness located next to a grey harness behind the knee bolster.

But if the signals come on when you turn on the parking lights than you will also need to check the wiring from the rear left signal and follow that light green wire all the way back to the turn signal and hazard flasher unit.

This should fix your problem, but if not than your problem may lay within the the wiring between the turn signal/hazard switches and the turn signal and hazard flasher unit.

Also you may have a burnt circuit in the junction block. This block is where the light green from the rear left signal and front left signal meet. Don't have a description but if you cannot find it let me know and I will go out to the yard and look myself and let you know.

Apr 22, 2009 | 2004 Dodge Intrepid

1 Answer

1996 4runner Front Turn signal failure


the problem might be a flasher unit. try to replace it

Apr 03, 2009 | 1996 Toyota 4Runner

1 Answer

No passenger side brake light. right flasher module going bad .


Check the rear bulb socket. You might even try wiggling the wires on the back of the socket while you have the signal on.

Mar 26, 2009 | 1995 Chevrolet Tahoe

Not finding what you are looking for?
1991 Chevrolet Astro Extended Logo

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...