Question about 1999 Plymouth Voyager

1 Answer

I am trying to put on seet covers for my 1999 plymouth voyager but they get stuck on the arm rests. Is there an easy way to take off the arm rests?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 211 Answers

As i recall there should be a hole under the arm rest right were it connects to the seat should be 1 big bolt take it out and put back after you put on covers. you have to stick your finger in the hole to find the bolt

Posted on Aug 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Looking for a 3.3L voyager relay diagram for a 1995 plymouth

very possible as it would be to accommodate the upmarket version

Sep 13, 2017 | 1999 Plymouth Grand Voyager

1 Answer

Can a suspension cradle shift on a 1999 plymouth voyager

Yes If It Was Hit Hard enough It Could Have Changed Shape!
Its Not Hard But takes Time.

Mar 29, 2013 | 1999 Plymouth Voyager

1 Answer

I just bought a 99 voyager. the lifters are taping pretty good on the back 3 cyl. what is the easiest way to fix this?

This may not be so easy, you will need to remove the valve cover and check to see if its abad rocker arm or worn pushrod or if its a lifter , you will need to check each cylinder, spin engine to make one valve open and check for play in the other, this way if the intake valve is open that means the exhaust valve it closed and theres no pressure on the pushrod or lifter and if that is loose you will need to look at the rocker and push rod to see whats bad, you will do this to each cylinder to check all lifters and rockers, good day.

Jul 16, 2011 | 1999 Plymouth Voyager

1 Answer

How do i rplace brake light on 1999 plymouth grand voyager

OPen the back hatch. there are 2 srews on the door jam at the assembly remove them and pull the assembly out. It has clips that also hold it in. just pull it at the top and bottom and it will come out. You'll see how to do the rest.

May 01, 2011 | 1999 Plymouth Grand Voyager

1 Answer

Were is the fuse for the horn on a 1999 plymouth voyager van

Power Distribution Center (PDC)

Power Distribution Center (PDC) (1997-2000)

The picture shows the horn relay is the second row down on the left and side of the Power Distribution Center (but the diagram didn't transfer over to
I would use a fuse tester to test the rest of the fuses in the PDC.

Oct 30, 2010 | 1999 Plymouth Voyager

1 Answer

My electric window on the drivers side and the rear vent window do not operate. Can this be a defective master module on the drivers side door.

It is USUSALLY just the rocker switch in the door there. Water drips on it when window is open during wet weather. This causes the contacts under that switch to corrode. Those are simple an easy to replace. Pop off the inside door panel (screw under the inside door latch handle, 2 or 3 screws under the arm rest - then plastci pop screws all around the sides and bottom. these can just pull out. Then it lifts off the top ledge. turn it and you'll see the switch still attached to the panel. try cleaning - will probably need replacement.

Aug 17, 2010 | 1999 Plymouth Voyager

2 Answers

Hello! 1999 plymouth voyager instrument cluster not working! Wat is the problem?

Instrument panels are computers in them selves. it could have blown. check fuses and have it put on a diagnostic scanner and checked for any codes

Jun 16, 2010 | 1999 Plymouth Voyager

1 Answer

1999 Plymouth Voyager engine compartment fuse/realy diagram

I have to assume you have lost the cover for it, as the schematic/Map, is on the underside of it.

May 24, 2010 | 1999 Plymouth Grand Voyager

1 Answer

After replacing the wiper motor and linkage bushings on my Grand Voyager SE, the wiper arms stop in the straight up position when ''at rest''. Help please

Remove the arms,and place them back on where they need to go,do not turn the wipers on,do this as they set now.If the wiper blades when turned on go off the left side of the windshield ,then you will have to remove everything again,and move the wipers down in the rest position,and align everything up to the rest position,with the wipers at rest,and the motor at rest.

Jan 22, 2010 | 1992 Plymouth Grand Voyager

2 Answers

1999 plymouth voyager front windshield wipers not working proper

Sure pull the cover off the arm at the base(by the bottom of the windshiel) under that you will find a bolt. Unbolt the arm and pull it off then adjust both arms so that they do not entangle at the high point. You can turn on the wipers and when they reach the high end quickly shut off ignition they will stop at this position so you can adjust them, This is what we would do at the shop for about 200 bucks. Take your time and be sure to tighten everything up when you're don and you will do great. Have fun.

Nov 29, 2008 | 1999 Plymouth Voyager

Not finding what you are looking for?
1999 Plymouth Voyager Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides