Question about 1994 GMC Sierra

1 Answer

"How to remove and replace a AC Clutch on a 1994 GMC Sierra 5.7?"

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 38 Answers

Depending on witch compressor you have they all are very straight forward , just remove the screws that hold the out side plate to the electric clutch and find the screw that holds everything together in the center ,remove it and it should slide out with no problem. get a replacement and install it the reversed way

Posted on Aug 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 GMC air cond. AC clutch wont engage. system is charged. relay, fuze,and low pressure switch are replaced.


ac compressor clutch coil open or short. wire cut or open to ac clutch.2 wires one is ground the other power, remove connector ac compressor then probe with test light between the two wire

Aug 05, 2013 | 2003 GMC Sierra 1500

2 Answers

How to remove the a/c clutch from a 1998 gmc sierra 1500 5.7 l


I believe this AC compressor is the same as my '95 Astro. The clutch is pressed on to the compressor shaft. You should see a threaded hole in the center of the clutch and a threaded screw in the center of that hole. To get this off you have to have the proper puller. It threads into the clutch and has a screw that you tighten against the end of the screw in the clutch. This pulls the clutch off the compressor (maybe, if it isn't frozen to the shaft). FYI, I just replaced my AC compressor and found that a new compressor with a new clutch was only about $40 more than the clutch alone. The puller cost $30.) Of course, if you replace the compressor you have the work of some parts in the AC system and recharging it. There are some good web sites with good pictures and instructions you may want to look into before you decide. I found that when I replaced the compressor, I had to replace the accumulator and compressor oil and there is some question about flushing the AC system when you install a new compressor. Hope all this helpful. Good luck.

Apr 22, 2011 | 1998 GMC Sierra

1 Answer

The electrical connector on the a/c unit broke off. Do I need to replace the entire a/c unit or the clutch assembly or what?


THE ELECTRICAL TERMINALS ON AC CLUTCH COIL IS BROKEN OR DAMAGED THE CLUTCH COIL HAS TO BE REPLACED.YOU DONT HAVE TO REPLACE THE WHOLE COMPRESSOR.YOU WILL NEED COIL REMOVER TOOL AND BEARING DRIVER TOOL.

Jun 18, 2010 | 1993 GMC Sierra

1 Answer

Is it fairly easy to install a clutch master cylinder (1994 gmc sierra 2500)my main concern is disconnecting and reconnecting the push rod to the clutch pedal through the little hole in the fire wall is is...


it is very easy to replace the parts, bleeding the air is the real problem, u will need to buy a Mityvac brand vacuum clutch bleeding tool, with out it you will never get the air out of the system after the parts are replaced, also always replace the clutch master and the clutch slave at the same time.

Jan 11, 2010 | 1994 GMC Sierra

1 Answer

My gmc serria shifts into first and second very hard, rest are smooth and harddly noticable


Sounds like the clutch is starting to go out, my Sierra did the same thing between 3rd and 4th. Time to get the tranny overhauled or replaced.

Dec 23, 2009 | 1994 GMC Sierra

1 Answer

We have bled the lines on a 1994 gmc sierra and are getting no tension in the clutch what do we do?


From your comments, your clutch master is no longer
working. Check your clutch master, and replace all the
worn out parts. You can buy all of these in one pack,
specify Clutch Master Repair Kit for 1989 GMC Sierra.

Oct 05, 2009 | 1989 GMC Sierra

1 Answer

How to replace a starter on 1994 gmc sierra 1500 with a 350 engine


unhook the battery, there are 2 wires on the starter solenoid, 1 is a 5/16 nut and the other is a 9/16 nut remove those wires. this maybe easier to remove the heat shield first. next ther are two 9/16 bolts holding the starter in position, remove, and the starter will come out, about a 15min job

Sep 27, 2009 | 2000 GMC New Sierra 1500

1 Answer

AC does not work, clutch will not engage


Most likely low or out of freon.There is a low pressure cut-out switch that open's when low on freon to prevent damage to compressor.

Aug 04, 2009 | 1994 GMC Sierra

1 Answer

1994 gmc sierra truck, have no clutch pedal at all, goes right to floor without pressure


Probably blew the rubber diaphram in the clutch master cylinder. Rebuild kits are fairly cheap and easy.

Jul 07, 2009 | 1994 GMC Sierra

Not finding what you are looking for?
1994 GMC Sierra Logo

392 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...