Question about 2001 Jeep Grand Cherokee

1 Answer

How to remove back door panel - 2001 Jeep Grand Cherokee

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Check out www.wjjeeps.com as it has full instructions on how to remove all panels

Posted on Aug 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove door panel from hyundai santa fe


A door panel removal tool works best, but if you have a stiff putty knife about 4" long and 1 1/4" wide it will work if you are careful. Start at the bottom of the panel and work your way around. Insert the blade all the way in between the panel and the door with the edge of the blade right next to the plastic fastener. Then pull the tool handle away from the door slowly. It will take a bit of pressure to get the first one or two clips to release.

The other steps I follow to remove this panel are as follows:

1. Remove the screw in the trim behind the door handle and then remove the trim piece.

2. Remove the door release cable from the handle.

3. Remove the door handle mounting bolts and then remove the handle.

4. Remove the three door panel mounting screws: 2 on the back edge of the panel and 1 in the door pull cup.

5. Separate the panel edges from the door. (see above) Lift the panel up starting with the back edge first to free the top lip of the panel from the door.

6. Disconnect the electrical connectors from the switches and light. (You may need a very small flat blade screw driver to depress the locking tabs on the switch connectors.)

plz rate this solution as i have a whole page of unrated posts, thanks

Aug 29, 2010 | 2003 Hyundai Santa Fe

1 Answer

Trying to remove rear door handle on chrysler lhs 99


Hello, to remove and replace the rear door try the following:

1. Disconnect the negative battery cable from the battery of your Chrysler LHS. You can accomplish this with an open end wrench, to prevent any injury or short in the electrical system as you are working on the door lock switch. Place the negative battery cable out of the way so it does not touch any metal parts.


2. Undo any screws that are holding the lower door panel to the door with a screwdriver. Unclip the plastic hold clips that are attached to the back of the panel by carefully pulling them away by hand.

3. Locate the electrical connector wires. These wires run behind the panel to the door arm rest and detach each wire connector by hand. Remember how the wires were attached so you can put them back the same way when it is time to reattach them.

4. Lower the door panel away from the door. Then, remove any screws holding the upper door panel in place. Remove the door handle pull cup that covers the door lock switch and door handle by carefully popping the cover off after you have removed the screws holding it in place.

5. Detach the upper door panel from the door. You can do this by pulling it away carefully from the plastic clips. Move the upper door panel out of the way and locate the door lock actuator switch. Remove the screws from the actuator switch that are holding it in place and disconnect the electrical wires attached to the back of the switch.

6. Replace the old door lock actuator switch with a new one. This replacement can occur by connecting the electrical wires to the back of the new switch and reattaching the switch to the door frame with screws. Put the upper door panel back in place, securing it to the door frame with plastic clips and screws.

7. Reattach the door handle pull cup to the upper door panel with screws. Then, put the lower door panel in place and reattach the electrical wires to the window switches underneath the armrest. Attach the lower door panel to the door frame with plastic clips and screws.

8. Attach the negative battery cable to the Chrysler LHS battery with the open end wrench.

Thanks













































Jul 27, 2010 | 1999 Chrysler LHS

1 Answer

I need to replace side mirror on the passenger side,but not sure how to remove door panal to getto the plug


First roll down the window and remove the inside mirror cover the remove the push pins in the back of the door panel ( push the center in to the 1st click then remove the pin from the door panel . With the pin out of the door panel push the center pin back out of the push pin retainer so it will be ready to go back in)Then remove the screw cover behind the door pull (just pops out) remove the 2 screws . Use a door tirm tool to release the push pin retainers that hold the trim to the door and lift the door panel up and off the top edge of the door . disconnect the elec connectors.

Feb 23, 2010 | 2006 Chevrolet Malibu

1 Answer

How do you remove the inside paneling to fix a broken door handle?


4-Cylinder Engines
  1. Remove the screw in the door handle trim, slide the handle assembly forward, and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
  2. Carefully pry off the cap(s) in the armrest pocket, then remove the screw(s).
  3. Carefully pry off the cap under the armrest and remove the screw.
  4. Using a suitable trim panel removal tool, unsnap the door panel from the door frame.
  5. Unplug the electrical connectors for the power windows, power mirror and courtesy light.
  6. Carefully lift the door panel up and away from the door frame.
  7. Installation is the reverse of the removal procedure.

V6 Engine
  1. Remove the screw in the door handle trim, slide the handle assembly forward, and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
  2. Carefully unsnap the rear of the speaker grill, lift and pull back to release it and remove the grille.
  3. Remove the panel mounting screws located around the perimeter of the speaker.
  4. Remove the cap and screw in the pull pocket of the armrest.
  5. Slide the pocket back slightly to release the front hook, then lift up, detach the electrical connectors and remove the pocket assembly.
  6. Using a suitable trim panel removal tool, unsnap the door panel from the door frame.
  7. Carefully lift the door panel up and away from the door frame slightly and disconnect the speaker connector.
  8. Installation is the reverse of the removal procedure.

Oct 13, 2009 | 1999 Honda Odyssey

1 Answer

Do i have to remove the door panel to take off door speaker covers? Speaker covers are starting to rust and want to remove all 4 speaker covers on door just to paint them. Trying to remopve without...


I believe that your speaker covers are clipped in through the back of the panel and won't come out through the front without breaking some of the clips. The proper way would be to remove the door panels and remove the covers out the back of the panel.

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the panel

Sep 24, 2009 | 2002 Lincoln LS

1 Answer

Lneed to remove drivers side door panel


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Jul 16, 2009 | 2001 Jaguar S-Type

1 Answer

2005 Dodge Grand Carvan / Removing sliding door panel


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Jun 19, 2009 | 2006 Dodge Grand Caravan

2 Answers

Driver side power window stopped working


The door panel is held on by plastic clips and 5 screws. 3 screws are on the bottom and 1 in the pull cup and 1 in the inner door handle.Then grab one of the corners and give a small tug, when you get some of the clips to pop out then proceed around the whole panel. To replace the panel take the clips out of the door with a fork and slide them back into the panel and then line it up on the door and use your hand like a hammer and bang the panel back on. Hope this helps

Jan 12, 2009 | 2004 Chrysler Sebring

1 Answer

Back door panel removal


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Oct 18, 2008 | 2006 Toyota Sienna

1 Answer

A4 96' back window slipped down


Removal is actually very easy and only requires a philips screwdriver and about five minutes. Open the door and look at the top of the door panel at each end - there is a screw at each top corner - one that screws in at the front, pointing toward the rear of the car, one screws in at the back pointing toward the front. Remove those. Then, inside the handle that is used to pull the door shut, there's one screw there, at the back of the inside of the handle. Remove that. That frees up the trim piece that forms the inside of the pull handle. Slide it down and pull it out (it's kind of tough to do, so if it's not coming right off, don't worry, just pull down harder and it will). When you remove that, it exposes a fourth screw that anchors the door panel to the door frame. Take that out, and then the door panel lifts up and off the door. Be sure that you push the door lock down before lifting the door panel off, so that it's easier to remove the panel. When you start to reinstall it, pull the lock shaft up so that it's easier to align it with the hole in the top of the door panel, and reinstall the four screws you removed.

Sep 07, 2008 | 1993 Audi 100

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...