Question about 1998 Isuzu Trooper

1 Answer

I had my 1998 Isuzu trooper repaired for the cylinder heads, when the mechanic returned the car, he told me that the computer showed that the oxigen sensor located before the catalytic converter,on the passanger side needed to be replaced, lately i notice that when the car goes in slow speed it slips, constantly, I haven't replace the sensor, could it be cause of the slippage?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

Slippage is terminology for transmission problems. If the engine revs but does not climb up to speed right away, this is slipping. Your O2 sensor would not cause this problem. I my guessing this slipping did not exist before the cylinder head replacement? If not, perhaps an electrical connection was not properly connected.

Posted on Aug 05, 2010

  • 4 more comments 
  • Joseph sarria Aug 05, 2010

    Thank you, the engine revs briefly and then climbs to speed right away , it is done while it goes very slow, if electrical connection any suggestions?

  • GetMeOttaHere Aug 05, 2010

    TCC connector ( torque converter clutch solenoid) or a possible loose or not connected engine ground wire.

  • Joseph sarria Aug 05, 2010

    Thank you, for your help, I forgot to mention that the check engine light, comes on and off, does this mean anything to you?

  • GetMeOttaHere Aug 05, 2010

    Yes it does, this means the PCM sensed a fault in a circuit or component. There is a trouble code that is stored in the PCM memory, and the light alerts the operator and a technican of a problem. You can have this code retrieved from the vehicle, Autozone or any other quality automotive supply store will come out and perform this procedure for FREE. It my be a good idea at this pint, unless you have a scanner or trouble code.

  • Joseph sarria Aug 05, 2010

    One last question, if this code is retrieved, will that find the solution, will the problem go away?

  • GetMeOttaHere Aug 05, 2010

    No, this will give a place to start with diagnosis and repair.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much for lifters on a 1998 izusu trooper? And will that make you engine nock?


Lifters generally make a tick, tick, tick noise. If you have a low tone knock, you may have more severe issues, or what you may have is heavy carbon build-up on the pistons, contacting the cylinder head(s). What I suggest first is to use fuel injection cleaner and add it to the fuel tank a few times. You can go to your local part store and see what other products they have, such as "Seafoam," to assist in carbon removal. Extreme conditions may actually require the removal of the cylinder head(s) to gain access to the top of the pistons to physically scrape the carbon from them.

Oct 10, 2012 | 1998 Isuzu Trooper

1 Answer

Oxigen sensor


OK, so now I know that you have a 1999 Isuzu Trooper Equipped with a 3.5L V6 DFI DOHC engine, 4-wheel drive, four wheel disc brakes, four wheel antilock system, 108.70 in. wheel base, with a standard curb weight of 4465 lbs.

WHAT ABOUT "oxygen sensor"???

Apr 14, 2012 | 1999 Isuzu Trooper

1 Answer

Where is the location of camshaft sensor 1998 isuzu trooper


if its diesel 4JX1 its in top cam belt cover cant miss it, sensor is very clearly visible.
if its petrol V6 (6VD1 or 6VE1) its in left head at rear behind inlet manifold
these pictures are for petrol V6, Jackaroo(Trooper) and Holden Rodeo are the same.

stevenhurc_21.jpg



stevenhurc_22.jpg

Apr 10, 2011 | 1998 Isuzu Trooper

1 Answer

Blown Head Gasket.


hope you can see this, may need to save in paint then zoom

ee9bd64.gif

May 28, 2010 | 1989 Isuzu Trooper

2 Answers

Looking to buy a 1998 isuzu trooper but the check engine light is on. should i buy anyway


you can bring your vehicle to autozone or your local parts place for a "free" computer scan where you can then recieve the diagnostic trouble codes and address the issues at hand

May 27, 2009 | 1998 Isuzu Trooper

1 Answer

97 isuzu hombre cylinder 2 misfire


1998 isuzu rodeo wont start no spark,no injector pulse

Jan 08, 2009 | 1997 Isuzu Trooper

4 Answers

Diagnosing a misfire


good luck i have the same car and it has been a nightmare from day one . everything is expensive to repair mine showed a mis fire in same cylinder had to supposedle head gasket was bad and gas was gettting in causing misfire

Aug 15, 2008 | 1997 Isuzu Trooper

Not finding what you are looking for?
1998 Isuzu Trooper Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...