Question about 2008 Chrysler Town & Country

2 Answers

2008 Chrysler Town & Country. Need to remove inside passenger door panel to access wiring harness for replacing outside passenger side mirror. I removed the 2 torx screws on the door panel (one located behind the door latch and the other in the inside door handle). I tryed to pry off the panel but was afraid of breaking it. Is there a trick to removing the door panel?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 12,962 Answers

There are clips that hold it in place. Using a flat blade screw driver carefully pry it off. Do not forget to remove arm rest if one is there.

Posted on Sep 02, 2017

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 1,295 Answers

There are about 10 fasteners holding it in place. Check with your library to see if they offer online car repair manuals. If not, invest in a 1-year subscription to alldatadiy.com and print out the diagrams.

Posted on Sep 02, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 81 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

  • 1 Answer

SOURCE: fuse for stereo/cd in chrysler town and country minivan

Its in the box next to the battery and i had the same problem.The fuse is on the first line top.

Thanks

Posted on Mar 08, 2009

chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

keemo68
  • 1263 Answers

SOURCE: radiator fan relay,2001 chrysler town country

the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays

Posted on May 08, 2009

defadad
  • 351 Answers

SOURCE: removing and replacing passenger side mirror 2002 town and country van

there should be a triangle shaped plastic section on the interior of the door behind the mirror, check it for a little plastic screw cover to remove it or you may just have to lever it gently to remove it.
once it is off it exposes the mirror retaining bolts which you undo to remove the mirror, I presume it has electric mirrors and if that is the case you will have to find the electrical wire plug for the mirror and pull it apart, replace mirror in reverse order of removing

Posted on May 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Neither front windows work at the master switch but passenger side works only on the passenger side . I replaced the master switch and same thing . 2008 Chrysler Town and Country


Friend of mine had a similar issue. Turned out to be frayed and broken wires in the rubber door jamb boot. You'll need to trace it down using a meter or test light.

May 12, 2015 | 2008 Chrysler Town and Country

4 Answers

Replace the review mirror


You need to remove the plastic plate that cover the mirror joint from the inside and undo the three bolts.

Oct 30, 2008 | 2006 Chrysler Town & Country

2 Answers

2003 Town & Country Van- trying to replace the drivers side mirror but can't find the plug inside ... please help.


you will need to remove the door panel the connection goes down about 10 inches from mirror,

Aug 07, 2010 | 2002 Chrysler Town & Country

1 Answer

Hi I have a 2006 Town and Country and I need to replace the passenger side outside mirror. How do I repair this?


take off the door panel on the inside and you'll find bolts that hold it on under there

Jul 04, 2010 | 2006 Chrysler Town & Country

1 Answer

Looking to replace passenger side mirror on a 2006 Town and Country. Anyone have Instructions available?


    Remove Old Mirror
  1. 1 Open the side door to the Chrysler Town & Country, and find thescrew that holds the side mirror molding in place.

  2. Take the screw out and remove the molding panel that attached around the outside of the power mirror.

  3. Remove the bolts connecting the mirror to the door assembly. If equipped, unplug the power side view mirror wiring harness connector.

  4. Unplug the electric connectors, and pull the mirror out of the molding.

Jun 01, 2010 | 2006 Chrysler Town & Country

1 Answer

How do you change out a left side mirror assembly on a 2005 town and country?


1. Pop off the triangular piece that is just cosmetic on the upper flat part of the mirror where it is attached to the van.
2. Under this piece are two visible bolts which you will need a Torx driver to remove.

3. Open the passenger door all the way open and remove the 3rd bolt, which is exposed from the outside of the car.
4. Expose the wiring harness plug by doing the following:
a. Pull off the door weatherstripping along the top of the door and on the pillar (the part of the car to the left of the windshield) Do not completely remove the weatherstip - simply pull it away enough to execute the next step.

b. Remove the plastic pillar cover: it simply snaps in. Pull hard and it will pop off
c. Lift up the plastic cover over the speaker on top of the dashboard. This piece goes all the way across the dashboard. Simply lift it up enough to get your hands underneath it. There is no need to free it from the passenger side.

d. Follow the mirror wiring harness around the rear of the speaker (the side nearest the engine) and unplug it from the female connector at the right-rear of the speaker. There may be a wire clip at the left-rear of the speaker that you will need to get the wire out of.
5. Unplug the wire, remove the mirror, replace the mirror, reinstall everything

hope its work

Jan 11, 2010 | 2005 Chrysler Town & Country

2 Answers

How do you change a passenger mirror on a 2006 Chrysler Town & Country. The mirror is not broken just the plastic frame work.


If you're lucky, on the inside of the door, will be a triangular panel right behind the mirror that you can pop off. If you're not as lucky and it's one piece or the panel is blocked by the door panel, you'll need to remove the door panel to change it.

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the bolts holding the mirror onto the door

Nov 09, 2009 | 2006 Chrysler Town & Country

1 Answer

Removing and replacing passenger side mirror 2002 town and country van


there should be a triangle shaped plastic section on the interior of the door behind the mirror, check it for a little plastic screw cover to remove it or you may just have to lever it gently to remove it.
once it is off it exposes the mirror retaining bolts which you undo to remove the mirror, I presume it has electric mirrors and if that is the case you will have to find the electrical wire plug for the mirror and pull it apart, replace mirror in reverse order of removing

May 12, 2009 | 2002 Chrysler Town & Country

1 Answer

How do I remove a drivers side mirror from a 2001 Chrysler Town & Country?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Mar 19, 2009 | 2001 Chrysler Town & Country

2 Answers

Repair a side mirror on a car


1. Pop off the triangular piece that is just cosmetic on the upper flat part of the mirror where it is attached to the van.
2. Under this piece are two visible bolts which you will need a Torx driver to remove.

3. Open the passenger door all the way open and remove the 3rd bolt, which is exposed from the outside of the car.
4. Expose the wiring harness plug by doing the following:
a. Pull off the door weatherstripping along the top of the door and on the pillar (the part of the car to the left of the windshield) Do not completely remove the weatherstip - simply pull it away enough to execute the next step.

b. Remove the plastic pillar cover: it simply snaps in. Pull hard and it will pop off
c. Lift up the plastic cover over the speaker on top of the dashboard. This piece goes all the way across the dashboard. Simply lift it up enough to get your hands underneath it. There is no need to free it from the passenger side.

d. Follow the mirror wiring harness around the rear of the speaker (the side nearest the engine) and unplug it from the female connector at the right-rear of the speaker. There may be a wire clip at the left-rear of the speaker that you will need to get the wire out of.
5. Unplug the wire, remove the mirror, replace the mirror, reinstall everything

Dec 22, 2008 | 2001 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...