Question about 2006 Chevrolet HHR

1 Answer

How to replace rear stop/turn signal bulb. - 2006 Chevrolet HHR

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

You need to remove the access panel by the lamp assembly. Small panel that is square at the bottom, arched at the top. Use a flat head screw driver to pop it open and stick your hand in and remove the socket. If you can see the amp you took the wrong panel off. The access is about 2 inches from the liftgate opening. Keep in mind that this can be replaced under warranty.

Hope helps.

Posted on Aug 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Town and counrty front right signal light flashing faster, rear light stop flashing


the signal indicator lights are suppose to flash in perticular time interval which is connected to a timer relay when the light flashes faster that means the other light is not working and the relay is getting double the current and moving faster so check the other light either the bulb is fuse or the current is not reaching up to the bulb

Aug 22, 2012 | 2005 Chrysler Town & Country

2 Answers

Right rear turn signal blinker blinks very fast


Your right rear turn signal bulb is blown.Replace the bulb and the fast blinking will stop.

Nov 26, 2011 | 1999 GMC Suburban

1 Answer

I am trying to replace aleft rear turn signal bulb on a 2005 lacrosse. I removed two wing nuts but cannot remove assmbly. Is there another wing nut holding it in. I cannot find it?


3 wing nuts. here is the info needed.

gmlogoflat.gif Service Information
bhome.gifbpublication.gifbnumsrchbutton.gifbnews.gifymkbutton.giffeedback.gifbhelp.gif
2005 Buick LaCrosse ' Allure, LaCrosse VIN W Service Manual ' Body ' Lighting Systems ' Repair Instructions ' Document ID: 1537542 Tail Lamp, Turn Signal Lamp, High Mount Stop Lamp, License Lamp, Backup Lamp Replacement - Rear
1537540.gif
tif.gif
Callout
Component Name
Notice: Refer to Fastener Notice in the Preface section.
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .
Turn Signal/Stop Lamp Assembly Replacement - Rear 1
Nut, Turn Signal/Tail Lamp (Qty: 3)
Tip
Pull back rear compartment carpet to gain access to lamp.
Tighten
2 N·m (18 lb in)
2
Lamp, Turn Signal/Tail Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.
License Lamp Replacement 3
Screws, License Lamp (Qty: 2)
Tighten
2 N·m (18 lb in)
4
Lamp, License Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.

Jul 29, 2011 | Buick LaCrosse Cars & Trucks

1 Answer

How do replace driver side headlight bulb? What size do I get?


Go to your local auto parts store.Ask at the counter,give them your make and model and year.

High & Low Beam Headlamp Light Bulb Size: 9007
Parking Light Bulb Size: 194NA
Front Turn Signal Light Bulb Size: 7507 Or 2827
Rear Turn Signal Light Bulb Size: 7507
Tail Light Bulb Size: 7443
Stop Light Bulb Size: 7443
High Mount Stop Light Bulb Size: 7506
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 921
Front Side Marker Light Bulb Size: 194NA
Rear Sidemarker Light Bulb Size: 7443
Dome Light Bulb Size: DE3175
Trunk/Cargo Area Light Bulb Size: DE3022

The bulb is in a socket which will twist out,then there may be a clip that holds the bulb in.

Jun 25, 2011 | 2003 Mitsubishi Lancer

1 Answer

How to replace bulb in front bumper turn signal housing 1995 jag xj6


hello,
  • Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.

  • Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.

  • Remove the front turn signal light unit in the bumper to change the turn signal bulb. Push gently on the inside edge and insert a blade between the bumper and the lens at the outside edge. Compress the spring and remove the lens. Fit a new lamp by inserting it into the plug. The side marker light is changed using a similar process.

  • Open the trunk to replace the rear fog light, stop light, tail light, reversing light and turn signal light. Remove the rear light cover and turn the bulb holder fastener 90 degrees counter clockwise. Remove the expired bulb, fit a new one and replace the parts, turning the bulb holder clockwise.

  • Thanks..

    May 21, 2011 | 1995 Jaguar XJ6

    1 Answer

    How do I change a rear turn signal bulb in a 1994 lincoln mark vii


    1994 was the mark viii. here is what you need to do.

    Lens/Bulb, Turn Signal-Rear

    Removal and Installation

    To remove the plastic socket, turn the socket counterclockwise to the stop, and remove the socket. Remove miniature bulb from socket. Install miniature bulb in socket. Index the smallest tab for locating the three locking tabs, then press the socket into the rear lamp and rotate clockwise to the stop.

    1. Remove retainer (unscrew) attaching the luggage hold down net and luggage compartment side trim.
    1. Pull trim down to expose the lamp attaching nuts


    1. Hold rear lamp in place and remove the three attaching nuts.
    1. Pull rear lamp away from vehicle far enough to remove the two lamp socket and wiring (13410) and remove the rear lamp .
    1. Replace miniature bulbs , if necessary.
    1. To install, reverse Removal procedure. Tighten nuts to 5.2-7.2 Nm (46-63 lb-in

    Sep 23, 2010 | 1994 Lincoln Mark VIII

    1 Answer

    How do you replace the tail light bulbs on a 2006 Pontiac Vibe


    Tail Lamp: Service and Repair
    TAIL LAMP REPLACEMENT
    REMOVAL PROCEDURE
    1. Open the rear compartment lid.
    2. Remove the rear compartment trim panel (4).
    3. Disconnect the tail lamp electrical connectors.
    4. Remove the following components from the vehicle:
    - The 3 nuts (3)
    - The tail lamp (7)
    5. Remove the following from the tail lamp:
    - The stop lamp socket (2)
    - The turn signal lamp socket (5)
    6. Remove the following from the lamp sockets, if necessary:
    - The stop lamp bulb (1)
    - The turn signal lamp bulb (6)
    INSTALLATION PROCEDURE
    1. Install the following to the lamp sockets, if removed:
    - The stop lamp bulb (1)
    - The turn signal lamp bulb (6)
    2. Install the following to the tail lamp:
    - The stop lamp socket (2)
    - The turn signal lamp socket (5)
    3. Install the tail lamp (7) to the vehicle. Secure the tail lamp (7) with the 3 nuts (3).
    NOTE: Refer to Fastener Notice in Service Precautions.
    Tighten the tail lamp nuts to 10 N.m (89 lb in).
    4. Connect the tail lamp electrical connectors.
    5. Install the rear compartment trim panel (4) to the vehicle.
    6. Close the rear compartment lid.

    Oct 30, 2009 | 2003 Pontiac Vibe

    3 Answers

    Blower motor and turn signals stopped working


    CHECK BLOWER MOTOR FUSE AND RELAY.IF ALL IS GOOD.CHECK TO SEE IF BLOWER IS GETTING POWER.IF NOT.SWITCH IS BAD.IF YES REPLACE BLOWER MOTOR.IF TURN SIGNALS STOP WORKING.CHECK FUSE FIRST.IF FUSE LOOK GOOD. CHECK BULBS TO SEE IF THEY ARE BLOWN.IF BULBS LOOK GOOD PROBLEM COULD BE WORN OR CORRODED BULB SOCKETS OR.BAD GROUND.OR THE TURN SIGNAL SWITCH IS BAD.

    Aug 24, 2009 | Plymouth Voyager Cars & Trucks

    2 Answers

    Right turn signal flashes too fast I have replaced my front turn signal bulbs a few times and within a couple days they stop working and the blinker on the inside flashes very fast. I have looked for the...


    littlejevans: The turn signal flasher works against the resistance through the bulbs both front and rear. The Malibu's had a problem with the rear light sockets which caused problems with the tail lights. Have you checked to see if the rear lights are functioning correctly?

    May 29, 2009 | 2005 Chevrolet Malibu

    1 Answer

    Jeep Liberty Left Rear Turn Signal Not Working


    sounds like the bulb you have is the wrong resistance the new noen bulbs will do this

    Nov 16, 2008 | 2004 Jeep Wrangler

    Not finding what you are looking for?
    2006 Chevrolet HHR Logo

    313 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...