Question about 2001 Hyundai Accent

Open Question

How to change a crankshaft sensor on a hyundai amica 2001

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1071 Answers

SOURCE: its a hyundai trajet,aa said crankshaft sensor not

it is inside the timing cover in most cases with hyundai the timing belt will have to be removed so the crank gear can come off the sensor is usually behind the gear especially if it is a 6cyl if it is a 4 cyl then the wire goes behind the timing belt make sure the timing marks are lined up so when you reassemble it is lined up

Posted on Aug 29, 2009

Testimonial: "Thank you for the advices Ill get cracking on it"

Ad
emissionwiz
  • 76109 Answers

SOURCE: crankshaft sensor location on 2001 oldsmobile

. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wIre CONNECTOR plug to the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery.

Posted on Jun 05, 2010

  • 94 Answers

SOURCE: need to change crankshaft position sensor for 2001 elantra

down by your crank shaft pulley you will find a sensor with 2 wires ruining into it and 1 bolt holding the sensor in remove the bolt and twist and pull on the sensor then slide the new sensor in then reinstall bolt and wire

Posted on Mar 08, 2009

ghost45
  • 1280 Answers

SOURCE: I have a 2000 hyundai Sonata, 6 cylinder eng. My

The sensor is located on the left hand rear side of the block (near the bell housing). It is held in place by a 10mm bolt. It's to the right of the exhaust manifold (LH - radiator side) on the V6. Once you purchase the new sensor you'll be able to identify it on the engine. The connector to this sensor is located in the illustration.
2cb09a4.jpg A word to the wise... replace the O2 snsr as well.

Posted on Oct 04, 2009

roniecon
  • 6826 Answers

SOURCE: were is the crankshaft position sensor located on 2001 chevy mali

It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Posted on Mar 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cam sensor 2002 hyundia accent 1.5?


    More images for Where is the cam sensor 2002 hyundai accent 1.5

    Hyundai Crankshaft Position Sensor Removal - YouTube

    ? 3:42
    https://www.youtube.com/watch?v=0YLYDU_5w8w
    Jul 12, 2012 - Uploaded by richpin06a
    Hyundai Elantra Crankshaft Position Sensor Removal.

    Hyundai accent 2001 - YouTube

    ? 2:44
    https://www.youtube.com/watch?v=fzqMNho3xIU
    Nov 25, 2012 - Uploaded by mig dups
    2000 Hyundai Accent GS turns over - no start. ... HyundaiCrankshaft Position Sensor Replace Timing Belt ...


Dec 26, 2015 | Cars & Trucks

1 Answer

Replace cam position sensor


The Atos has a timing sensor located at the bottom of the engine by the cambelt drive sprocket (gear). The drive sprocket is bolted to the crankshaft with a timing plate. The sensor is placed next to the timing belt.There are no cam timing sensors on the cylinder head. This is a very basic engine.

Jun 10, 2014 | 2006 Hyundai Atos 1.1

1 Answer

I have a Hyundai accent 1.5 diesel 2002. Turns over but will not start, changed glow plugs and diesel is coming through the injectors


I believe your problem is with your crankshaft sensor. You may not have had to change glow plugs. Your problem seems to be with spark. If you change this part ,the crankshaft sensor, you should be OK. This sensor is located at the left front of your engine. Please let me know how you make out. GOOD LUCK.

Sep 08, 2011 | 2001 Hyundai Accent

1 Answer

Poor running


CAMSHAFT POSITION SENSOR IS LOCATED BANK 1 ON BACK TOP ENGINE HEAD. YOU ALSO ANOTHER CAMSHAFT POSITION SENSOR ON BANK 2 ON TOP FRONT OF ENGINE.YOUR PURGE SOLENOID VALVE IS ON BANK 2 ON TOP ENGINE HEAD CLOSE TO CMP SENSOR ON BANK 2 ALSO.

Sep 11, 2009 | 2006 Hyundai Azera

1 Answer

Need to change crankshaft position sensor for 2001 elantra


down by your crank shaft pulley you will find a sensor with 2 wires ruining into it and 1 bolt holding the sensor in remove the bolt and twist and pull on the sensor then slide the new sensor in then reinstall bolt and wire

Mar 08, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
2001 Hyundai Accent Logo

Related Topics:

594 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...