Question about Mazda B2600

1 Answer

Have to keep turning key in ignition for a start

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

I believe your starter solonoid is bad

Posted on Aug 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO I RESET THE SERVICE LIGHT ON CHEV UTILITY PLZ \


Put key in ignition but not turned on.
Keep brake pedal depressed and keep trip meter pushed in.
Turn ignition to on but dont start car.
Wait and the millage will show.
Turn off ignition,next time you turn ignition on the service light will be out.

Sep 14, 2017 | Cars & Trucks

2 Answers

Key wont turn while in ignition


Change ignition barrel or get a new key cut try spraying lubricating oil down the barrel

Apr 20, 2013 | 2001 Buick Century

1 Answer

2001 s10 will jump start. After it sits, I try to start it, it won't start, but the ignition keeps dinging after I turn it off and take the key out. I can jump start it and the dinging stops.


its sounds like a bad ignition switch-try to jiggle it and see if its stop after you have turned key off- also those dinging sounds are to warn you that you have left something on -usually headlights or maybe even your dome lights which would account for your battery dying

Apr 01, 2013 | 1998 Chevrolet S-10 Pickup

4 Answers

Security light keeps going on, I'm not able to start it then... how do I disable this?


IF YOU AWAY FROM HOME. LIKE AT WORK, SHOPPING MALL OR STORE.WHEN YOU GET IN CAR AND IT DONT CRANK.PUT KEY IN THE IGNITION SWITCH AND TURN IGNITION SWITCH TO THE ON POSITION FOR 10 MINUTE.UNTIL YOU SEE THE SECURITY LIGHT TURN OFF. WHEN SECURITY LIGHT TURN OFF TURN OFF IGNITION SWITCH WAIT FOR 5 SECONDS. THEN TRY STARTING VECHICLE SHOULD START.TAKE VECHICLE TO DEALERSHIP.THEY WILL HAVE SCAN VECHICLE.YOUR PROBLEM COULD BE WORN IGNITION KEYS OR WORN IGNITION SWITCH ALSO FAULTY BCM.THE DEALERSHIP HAS TO FIX AND REPROGRAM THEFT SECURITY SYSTEM.IF YOU REPLACE KEYS, IGNITION SWITCH OR BCM. THE 10 MINUTE TRICK WILL GET CAR STARTED TO GET HOME OR SHOP.BUT DONT KEEP DRIVING BECAUSE IT WILL COME TO A POINT WHERE VECHICLE WONT CRANK AGAIN.

Nov 20, 2010 | 1999 Oldsmobile Alero

1 Answer

The key symbol appears


That's your immobilizer system light:
The Immobilizer System protects your car from theft. A properly coded master or valet key must be used in the ignition switch for the engine to start.
If an improperly coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to ON (II), the Immobilizer System indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to LOCK (0), remove the key, reinsert it, and turn the switch to ON (II) again.
The system may not recognize your key’s coding if another immobilizer key or other metal object is near the ignition switch when you insert the key. To make sure the system recognizes the key code:
Do not keep other immobilizer keys on the same key ring.
Use a plastic or leather key fob, not metal.
Keep other keys away from your vehicle’s key and the ignition switch while trying to start the engine.
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your car undriveable.
This indicator will also blink several times when you turn the ignition switch from ON (II) to ACCESSORY (I) or LOCK (0).
If the system repeatedly does not recognize the coding of your key, contact your Honda dealer.
If you have lost your key and you cannot start the engine, contact your Honda dealer.
Hope this lets you understand the light, and what should be happening.

Dec 16, 2009 | 2002 Honda Civic

1 Answer

KEY WONT TURN IGNITION


Your car uses a transonder key, a key with a small chip embedded inside. The transponder is matched to the immobilizer unit in your car. When the key is inserted into the ignition, the immobilizer searches for that transponder, if it's not near the ignition, the car will just keep turning over and not start. Your only real options are to replace the steering lock or buy a transponder bypass unit, which I do not recommend. Just do a google search.

Aug 09, 2009 | 2003 Honda Pilot

2 Answers

My car turns over like it wants to start but never connects. Also the security light came on yesterday and this never happens. What could be wrong?


 If you have the second ignition key's with you try it.  If not try this, it takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself. Good luck and hope this helps, keep me posted, be glad to help. 

Jul 20, 2009 | 2001 Pontiac Grand Am SE

1 Answer

Key Ignition Problem!!!


Manual trans cars have a lock that will not release the key untill you pust the button, switch, etc. It should be right beside the Ignition.

May 12, 2009 | 1996 Honda Accord

1 Answer

I lost my key and the ford dealership by my house sad i need to reprogram a chip but the car is a 1999 tuaruse and its to old to pull up what can i do


Here is the factory procedure to program a new key(s), I recomment only factory keys, you need to use the working key to do the procedure;
1. Insert a previously programmed coded key into the ignition.

2. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4(ON) position for at least one second, but no more than 10 seconds.

3. Turn the ignition to the 3 (OFF) position, and remove the coded key
from the ignition.

4. Within ten seconds of removing the previously programmed coded key, insert the other previously programmed coded key into the ignition.

5. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second but not more than 10 seconds.

6. Turn the ignition to the 3 (OFF) position, and remove the second key from the ignition.

7. Within twenty seconds of removing the previously programmed coded key, insert the unprogrammed key (new/valet key) into the ignition.

8. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second.

9. Your new unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and
then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash on and off rapidly. If failure repeats, bring your vehicle to your dealer to have the
new key(s) programmed.

To program additional new unprogrammed key(s), repeat this procedure
from step 1 for each additional key

Jul 25, 2008 | Ford Taurus Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8755 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...