Question about 1995 Plymouth Acclaim

Open Question

Can you tell me where a map sensor and a crank sensor are located at on a 1995 plymouth acclaim i have no idea my car will start up but the when u put the gas to the floor the car just wants to pretty much shut off u have to press it lightly i think this is the problem

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 6674 Answers

SOURCE: I am looking for a vacuum diagram for a 1995

This should be it.6365988.gif

Posted on Apr 09, 2010


SOURCE: MAP sensor location

look to the left of the air filter for a module with 1 vaccuum hose and three wires. It may be labled as a boost sensor. I had a 97 XE and that's where mine is

Posted on Jul 12, 2008

  • 1 Answer

SOURCE: 1995 Plymouth Acclaim Won't Start

What is it a Start Relay in Auto, 95 Plymouth Acclaim?
ANSWER: ________________________________________________________________________.
(1) On September 11, 2008 at 5:07 pm Miguel A. San Antonio [0] said:
1. 1995 Plymouth Acclaim Sedan, 4 cylinders. 2.5 litter Repair Fuel Pump Steps or Procedure?
Replace the Fuel Pump and still not start.
2. What I need to do to remove the Fuel Pump and put the new one in?
Remove the ground cable or negative cable of the Battery.

  1. Does I need to remove the negative cable of the battery and remove the outside gas tank cap or lid?
Remove the ground cable or negative cable of the Battery. Also remove the outside gas tank cap or lid.
  1. Does the pressure of the tank is already gone, ones the fuel pump is not working?
    There is not was pressure inside the gas tank, maybe because the fuel pump issue.

  2. How do you remove a filler neck of the fuel tank of 1995 Plymouth Acclaim?
    Was not easy repair job, to remove the filler neck of the gas tank. I have to disconnected first of the outside to be able to jiggle the filler neck to disconnect of the gas tank.

  3. I went over and double check the fuses, fuel pump relay, start relay and etc.
    And I think was the start relay issue. I just bought the start relay and I will find out when I get home. When I should installed the start relay, will find if it was the Start Relay.

  4. This is the list of repair I had done to the Auto right now.
    As follow ;
    1. Fuel Pump replaces. Flush the tank, remove the ¼ gasoline tank of the Fuel Tank.

    2. Put new gasoline in the Fuel Tank.

    3. Ignition Rotor

    4. Ignition Coil

    5. Ignition Pick-Up Coil

    6. Fuel Filter

    7. Fuel Relay

    8. Start Relay Auto Zone Price is $96.99 @ Pep Boys Price is $17.99 before TAXES.

    9. Used Start Fluid and Degreaser Fluid to clean the MOTOR, too.

    10. Which is the next step to follow if the Auto does not START?

    11. By the way, when the Auto was running the speedometer was sometime working and sometime died.

    12. ANSWER:
Please, sent the answer as soon you can to my e-mail address, as follow;
Miguel A. San Antonio

Posted on Sep 15, 2008

  • 2 Answers

SOURCE: Crank Position Sensor

what is a crank position sensor ,what does that do ..

Posted on Oct 08, 2008

  • 7 Answers

SOURCE: 1991 plymouth acclaim break & signal lights not working

try checking your ignition swich or your asd relay it is under the hood on the driver side mounted to the wall

Posted on Feb 19, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1995 plymouth acclaim-hight idle/where and how do I get to the ilde(high) screw? Thank you.

A 1995 Plymouth Acclaim is a fuel injected vehicle which means it does not have an idle screw like the older carbrated cars. Instead your cars idle is controlled by sensors and the cars on board computer. There is a chance you either have a bad sensor or a vacuum leak some where. Both will cause a high idle. I hope this helps you out.

Aug 25, 2011 | 1995 Plymouth Acclaim

1 Answer

I cant find the computer on my 95 plymouth acclaim do you know where to find it?

hi the ECM is located behind the battery on the fender wall....hope this helps

Feb 04, 2011 | 1995 Plymouth Acclaim

1 Answer

PLEASE HELP I don't have to listen to my

sometimes it helps to tell what engine it has. It should be obvious when the engine is looked at where it is. If its a V6, its under the timing belt cover, and you need to replace the timing belt, tensioner pulley,and cam and crank seals while its apart.

Nov 19, 2010 | 1991 Plymouth Acclaim

1 Answer

My 1991 plymouth acclaim went dead and won't start. I dont't have fire to the distributor?

I had the same problem with my 1991 Plymouth Acclaim 3.0 liter engine. Check to see if your SBEC (computer located next to car battery) has gone out. Replacing it should solve your problem.

Jul 06, 2009 | 1991 Plymouth Acclaim

1 Answer

No fire to spark plugs in a 1989 Plymout Acclaim

possible crank sensor. withour the crank sensor it doesn't know when to fire the spark plugs.

good luck

Jun 25, 2009 | 1989 Plymouth Acclaim

2 Answers

Car wont crank 1994 plymouth acclaim

Not sure what yor experiencing . Do you have crank no start or no crank no start? No crank no start is battery and cables issue. Crank no start is ignition , plugs, and fuel.

May 28, 2009 | 1991 Plymouth Acclaim

1 Answer

Speedometer not working

More than likely it's the speed sensor on the transmission. Unplug sensor, remove retaining screw and remove the sensor. Reverse to install new snsor.

May 27, 2009 | 1995 Plymouth Acclaim

1 Answer

My car keeps stalling after about 15 minutes

Fill the coolant & change the coolant sensor near the thermostat housing. The sensor is defective. This is a common problem with these engines. Do not overtorque the sensor. Max 14ft.lbs. Good luck!

Apr 22, 2009 | 1992 Plymouth Acclaim

Not finding what you are looking for?
1995 Plymouth Acclaim Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides