Question about GMC Sierra 1500

Open Question

I need to replace door hinge ***'y on my 1990 gmc pickup truck and the old hinges are bonded in place

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

short shadey
  • 421 Answers

SOURCE: 2001 Blazer door hinge pins and bushing replacement

you need a special spring compressing tool to remove and reinstall the hinge spring and then its a matter of removing the door installing the new bushing and rehang the door with new pins ive tried doing this while leaving the door on the car trust me its just harder that way good luck and please rate -jeff

Posted on Sep 01, 2008

  • 372 Answers

SOURCE: driver's door hinge

You will have to Mcgyver it....You can cut the pin out but usually anything u put in there wil not last long. Also usually the pin goes and the hinge holes get oblonged making it impossibble too repair. I used to cut the hinge out Cause its welded to the frame on most and weld on a new one....

Posted on Aug 06, 2008

  • 508 Answers

SOURCE: How to replace '96 Ford Explorer driver side exterior door handle

You will need to remove the door panel to gain access to the handle. Roll the window up or down as needed to get to the nuts that attach the handle to the door. You will also need to remove a rod the goes to the door lock. You will see the rod after the door panel is removed. Good luck.

Posted on Feb 18, 2009

  • 150 Answers

SOURCE: my problem is that the upper door hinge on my 2001

Most likely the hinge is not bad, but the hinge pin bushings are bad. You can buy the hinge pins and the bushings at your local auto parts store. They come in a kit. Hope this info is helpful.

Posted on Mar 22, 2009

  • 105 Answers

SOURCE: How do you change the door hinge pin? On 1997 lincoln town car?

you really don't change the pin,...change the whole hinge,...junkyard! junkyard! good luck, cracklin joe

Posted on Jan 08, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replace door hinge 2000 gmc sierra

How exactly are the hinges ruined? To change the door on Sierras you drop out the pivots the hinge swings on. If the hinge bodies are the damaged part it's going to cost you money. You will need to get a GOOD body work specialist to cut out the old hinges and re-weld new ones in. Get the specialist to check the body and frame in case the wind has bent something else.

Feb 01, 2018 | GMC Sierra 1500 Cars & Trucks


Fix Anything, House doors hinges, car door hinges ETC...

If you work around the house and around cars a lot like i do, next time you find a squeaky door, leave the WD-40 alone, go for the petroleum jelly instead, like vasoline. Remove one hingpin at a time, if they are eaisily removed and clean it, Then lightly coat it with the petroleum jelly, and reinstall. Move on and do the next one. If the pin can't be removed, brush it on right at the bushing or hinge split. It lasts a heck of a lot longer than oil and does not run. I did one of my most used doors, in my home, a few years ago. The thing is still as silent as a church mouse. My wife hates it, because she always thinks i am sneaking up on her. One of these days i will do the rest. I gave my gmc pickup door hinges the same treatment. It has 207,000 miles still on the original door hinge pins with very little wear.Good Luck. Bob.

on Jan 04, 2010 | GMC Sonoma Cars & Trucks

1 Answer

1995 GMC pickup. Cold AC will blow through all settings (defrost, front vents and flloor) but warm air will not come out the defrost. You can hear something click in the dash that you assume is some kind...

good work, the clicking noise you hear is the blend door trying to move. this door is what controls the temp. the most common reason is the actuator motor is bad but sometimes the door hinge breaks, this hinge slides into actuator and is used to move the door. you will need to locate it on the heater box by locating the noise and then remove the actuator and see if the hinge is broken, i will try to enclose some picture to help you. good day, hope this helps.johnjohn2_142.jpgjohnjohn2_160.gif

Sep 24, 2011 | 1995 GMC Sierra C1500

1 Answer

Need instructions on replacing drivers side door hinge pins and bushings

  • 1. Place masking tape on the inside edges of the door, on both the inside and outside of the door. 2. Remove the door spring by using a door spring removal tool. Insert the tool into the door spring, turn the knob with a screwdriver to compress the spring, then pull out the tool. 3. Set a 5-gallon bucket under the door. This will help support the weight of the door. 4.Place a nail punch under the hinge pin, and strike it with a hammer. Repeat this until the hinge pin begins to come out of the hinge. 5.Place the end of a flat-head screwdriver under the top of the hinge pin, then strike the screwdriver with the hammer to force the hinge pin out of the hinge. 6. Place the bushing on top of the new door hinge pin, and tap it into place with the hammer. 7. Insert the new hinge pin into the hinge. Tap on the hinge pin with the hammer and nail punch to force the pin into the hinge. 8. Insert the hinge spring back into the door, and release the tension on the spring removal tool. 9. Spray the door hinge with a lubricating spray or apply grease.

    I know there are a few directions but it is fairly easy to do. If you have access to an air hammer and a compressor you can use this in place of a manual hammer to make the process a bit easier.

    Hope this helps.

  • Mar 10, 2011 | GMC Sierra 2500HD Cars & Trucks

    1 Answer

    My 1990 GMC Sierra 1500 ha a problem with the

    You need to get the hinges on the door fixed. The bushings are worn out causing the door to sag. See a body shop.

    Mar 01, 2010 | 1990 GMC Sierra

    2 Answers

    My drivers side door drops every time I open my door. Is it because of the door hinge or do I need to replace the door pins?

    the hinge pins rides on brass bushings. if the door does not latch replace the pin and bushings with oversized ones available at Chevrolet parts department
    you will need a sring compressor which is available at Auto Zone

    Feb 20, 2010 | 1990 Chevrolet S-10 Blazer

    1 Answer

    Driver door will not close properly>

    These things can be a pain, cause I have one... Have you adjusted the striker mechanism? Your adjustments are basically the striker and the door hinges. It is possible that you have worn door hinge pin(s). You may need to adjust the hinges. Rick

    Apr 15, 2009 | 1990 GMC C1500

    1 Answer

    Doors on my truck

    You probably need new door hinges. Open the door, lift up on the door while watching the hinges, you should not see any movement at the hinge location. If there is play there, replace the hinges. To remove door hinges, place a floor jack under the door for support while u remove hinges. There should be some adjustment at the hinges, and door latch to fine tune the fit and how it closes. Good luck, let me know how u make out.

    Nov 11, 2008 | 1999 GMC Sonoma

    2 Answers

    Both Doors are shot

    are the doors sagging? if you lift up on the doors is there play in the hinges? you can buy new hinge pins and bushings for about $20 a side they are pretty easy to install and this should realign your doors to shut right -jeff ...also napa or autozone should have the parts or try online please rate

    Sep 12, 2008 | 1988 Chevrolet C1500

    1 Answer

    90 chev truck

    There is no door adjustment usually needed. On these trucks the hinge pin bushings wear out. open your door slightly, then try picking up on it by grabbing the end of the door and pulling up. if you are able to move it up and down, you need new hing pins and bushings. they are about 8 bucks each (2 per door) and are found at your parts store in the Help! section of hardware. good Luck.

    May 14, 2008 | 1990 GMC C1500

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    195 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts


    Level 3 Expert

    81400 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides