Question about 2002 Ford Explorer Sport

Open Question

I need to replace the pcv valve on my 2002 ford explorer sport, but I can't find it. I need to see images of where to find it.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: pcv valve

I have a 98 4L SOHC . The valve seems to be behind the intake manifold. The emissions diagram shows 2 hoses going to it. Local dealership swears Part #EV225 is correct. You would not believe how much of the internet is devoted to this situation

Posted on Sep 23, 2008

Ad
  • 92 Answers

SOURCE: 1998 Ford Explorer sport 4.0L 4x2 PCV Valve Location

the pcv is located on the rear(firewall) of the drivers side valve cover.turn counterclockwise and pull to remove be careful there are 2 small tabs inside the pcv hole in the valve cover(can feel with small finger) this is to hold valve in place so it wont leak.if you have a oil leak at the pcv a quick fix is to put a small amount of silicone around the pcv o-ring and install.wait hours for silicone to set up.

Posted on Oct 21, 2008

Handy Mike
  • 6 Answers

SOURCE: how do i replace the pcv valve on a 2000 explorer xlt v6 sohc?

On the passenger side of the intake manifold, coming off the bottom about the center of the engine front to back, you'll feel a hose that comes off a nipple. That hose makes a 90 degree bend and goes around to the rear of the motor. Where that hose meets the Y-connector from the other side of the intake you'll find the PCV valve. It's almost impossible to see it with the hood installed, and even tougher to reach it.

A good source of information for Ford Explorers can be found here

Posted on Oct 25, 2008

  • 1596 Answers

SOURCE: pcv valve :where is it located on a 1999 ford explorer sport 2wd

Look For A 3/8 th's Vacuum Hose Coming from The Base of Throtle Body Fallow it to the 2 Line PCV At Valve cover

Posted on Feb 10, 2009

  • 3600 Answers

SOURCE: 2002 Ford Explorer Sport, diagram to add freon

there is a port and it takes r123a and it has a green port on it but if it's leaked out you mave have to have it vachumed out, if you charge it be sure to get R134a with oil so that you don't burn up the pump, when the thing leaks it loses oil.

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Finding location of pcv on 2002 explorer sport trac 4.0 engine


Welcome to FixYa.com

7d5bca9.png68dc18d.png

Thank you for using FixYa.com, Regards, Lee Davidian


Thank You for using FixYa - a 4 THUMBS- UP rating is appreciated for answering your FREE question!!!!!

Sep 29, 2010 | 2002 Ford Explorer Sport Trac

2 Answers

Where is the pcv valve at the engine ford explorer sport 99


PCV Basics
PCV stands for Positive Crankcase Ventilation.
All car engines have a PCV valve and it is located on top of the motor's valve cover. There is a vacuum line attached to it. It pulls out of the valve cover and if you shake it, you should hear a marble knocking inside it. If you shake it and don't hear anything, it's bad. It costs less than 5 bucks to replace.


Location
* 4.0L is located in the valve cover near the brake booster
* 5.0L is located behind the intake manifold (engine rear)

NOTE-Most people that are asking actually want to know not only where is it but also how do you get at it to replace it.

Often answers say that you need to dismantle the intake manifold to get to it.
This is a major and unnecessary approach, for example, on the 2000 Explorer with a 5.0 V8

Below is an additional suggestion on how to access a PCV valve on an 2000 5.0 V8 Explorer

The PCV valve is on the rear of the intake manifold (the intake manifold is also on top of the crankcase so PCV valve has direct access to crankcase)

To replace valve and/or its bushing:
  • Disconnect one battery terminal, unbolt/unplug the PCM cable (Powertrain Control Module connector located on the firewall) and firewall ground connection, depress underneath tab and slide the main cable connector (located to the right of PCM connector) off its mount.
  • Move the cables to the right and now you can easily reach down behind the intake manifold to the PCV valve
  • Service valve and its bushing if needed, reverse actions to reassemble
Hope this helped (remember comment and rated this). Good luck.

Apr 05, 2010 | 1998 Ford Explorer

3 Answers

Pcv valve :where is it located on a 1999 ford explorer sport 2wd


It is located at the back of the engine near the fire wall. It is gray with a T connector at the top with two hoses coming off of the T and going forward into the intake manifold.

Feb 10, 2009 | 1999 Ford Explorer

1 Answer

2001 Ford Explorer Sport


pcv is on the back side(firewall) of the drivers side valve cover.held in buy lock tabs,turn then pull to remove.

Nov 10, 2008 | 2000 Ford Explorer

1 Answer

1998 Ford Explorer sport 4.0L 4x2 PCV Valve Location


the pcv is located on the rear(firewall) of the drivers side valve cover.turn counterclockwise and pull to remove be careful there are 2 small tabs inside the pcv hole in the valve cover(can feel with small finger) this is to hold valve in place so it wont leak.if you have a oil leak at the pcv a quick fix is to put a small amount of silicone around the pcv o-ring and install.wait hours for silicone to set up.

Sep 25, 2008 | 1998 Ford Explorer

1 Answer

Pcv valve


I know it attaches to a small hose and the body of the valve inserts into the head. Mine is on the right rear in a 2000 Explorer Sport. The guy at Autozone always is happy to help me when I ask...too short to get over the fender if I don't have a step or block to stand on. Not a very expensive part.

Jun 11, 2008 | 2002 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

733 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...