Question about 2001 Hyundai Santa Fe
If they knew what they were doing in the first place the internal issues will have been noticed.
Get your money back and go to a proper Hyundai dealer.
Write a formal complaint to Hyundai and I think your problem may get resolved.
Posted on Jul 24, 2017
That is about the cost of a new one
Posted on Jul 24, 2017
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: removal of santa-fe gearbox
hi there! i was a master tech for hyundai, common problem to say the least, many times i had this. please feel free to contact myself and i can take you step by step to resolve this.
Posted on Dec 11, 2008
SOURCE: 2007 Hyundai Santa Fe Limited
I was able to get installation instructions for the cross bars from http://www.capitolhyundai.com and from http://dealerfit.com. Thanks much to these folks for providing a pdf of these instructions free of charge!
Below is the text from the instruction set that worked best for me. The other instruction set was nearly identical but it had an alternate Step 2 which involved using a small plastic pry bar. I added that alternate Step below in the instruction step. Hopefully I'm able to insert the image of each instruction set so that the Figures are visible. Its actually not that easy getting the rear rail covers off and its pretty easy to crack them. I'd recommend gently rocking the covers for a couple minutes in order to loosen them up. Once you get the covers off, the rest of the install is a breeze and can be done in 2 minutes. If you have questions, go ahead and contact me. I also took several photos of my install and that might be helpul. Cheers!
SANTA FE 2008 PIN U8210-28000 Cross Bar Assembly Installation Procedures
Kit Contents: • (2) Cross Bar Assemblies Required Tools: • Flat Head Screwdriver
1. Carefully unscrew and remove radio antenna. 2. Grasp the rear rail covers with both hands. Squeeze and pull up & inwards (toward the center of the vehicle) to remove covers. Take care not to break off the tabs by lifting the rear section of the cover first (Figure 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 2. - Alternate Method - Locate notch in rear of each cover to insert plastic pry bar. Remove cover by prying up (with tool) and lifting rear at 45 degree angle (Fig 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 3. Check assembly clips for damage and dislocation. Replace if necessary. 4. Open the lever on one side of front/rear cross bar. Gently set the cross bar, with the arrows facing forward, into the channel of the side rails (Figure 2). Guide both sides into the track. 5. To adjust cross bars, open lever and place cross bars in desired location. Close lever (Figure 3). Try to move bars forward/back until they lock into place. 6. Reinstall rear covers by holding cover at a 45 degree angle and inserting the front tab into the rear of the roof rack. After aligning, snap cover in place (Figure 4). Be sure that the rubber lip does not interfere with the covers, and that the covers are fully seated. 7. Reinstall the radio antenna. Note: To remove the cross bars, remove the antenna, remove the covers, open lever of cross bar and slide to end of rail. Hold down locking fingers (on both RH/LH rear rail supports) with a flat head screwdriver (Figure 5). This will allow removal of cross bars from the rails.
Posted on Feb 24, 2009
This is from the factory service manual of your car:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Translation you need the dealer to do this.
Posted on May 22, 2009
The vehicle will run fine for a while until that cat goes out all the way, the only thing that might get you away cheaper than $1,000 is a wrecking yard cat, but then you still take risks. If the cat is bad its bad nothing to do but replace it.
Posted on May 29, 2009
Tips for a great answer:
May 01, 2015 | 2003 Hyundai Santa Fe
Mar 02, 2014 | Hyundai Santa Fe Cars & Trucks
Dec 04, 2017 | 2001 Hyundai Santa Fe
Well, you basically have only 3 choices:
1. Pay the fee at the dealership
2. Purchase the high-dollar equipment that is required to perform the programming procedure
3. Forget about adding another key fob to tor vehicle.
TECHNICAL SERVICE BULLETIN
90 - ELECTRICAL
Elantra 2001-2004, Santa Fe 2001-2004, Sonata 2002-2004, Tiburon 2003-2004, XG(NNN) NNN-NNNNand XG(NNN) NNN-NNNN2004
SECURITY SYSTEM KEYLESS ADAPTER CABLE
This bulletin supersedes TSB # XXXXX
The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03 or newer) and Data Link Connector (DLC) Cable.
The keyless adapter cable can be used on the following vehicles:
^ 2001 -2004 Elantra
^ 2001-2004 SantaFe
^ 2002 - 2004 Sonata
Apr 24, 2011 | 2005 Hyundai Santa Fe
Jan 23, 2010 | 2004 Hyundai Santa Fe
Sep 22, 2009 | 2001 Hyundai Santa Fe
Jul 04, 2009 | 2001 Hyundai Santa Fe
Jun 20, 2009 | 2001 Hyundai Santa Fe
Dec 02, 2008 | 2001 Hyundai Santa Fe
Apr 20, 2017 | 2001 Hyundai Santa Fe
62 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: