Question about 1995 GMC Yukon

1 Answer


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Rear differentials theres a plug on the side of the cover in the front side looking from the driveshaft it would be on the passenger side above the ear, stick a 3/8" ratchet head or extention in it and you can turn it out sometimes theyre a lil stuck so tap it with the extention in it to jar it a lil and should come right out, then fill it til it reaches the plug.

Posted on Aug 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I'm looking to replace the rear axle on my 1997 4 door 4x4 GMC Yukon 3.73 gears would a rear axle from a 1998 Yukon 4door 4x4 with 3.73 gears bolt directly to my 1997 Yukon

the housings will be the same
clue here --if the diff center comes into the housing from the front not a problem
if it comes in from the rear ( tin cover removed ) replace the complete housing as you will have to have expertise in resetting the bearing pre-loads for the diff center bearings

Jul 15, 2017 | GMC Cars & Trucks

1 Answer

How to remove oil pan gasket from 2002 GMC Yukon Denali?

I just changed my oil pan gasket on my 2001 GMC Yukon Denali. Once all bolts are off the oil pan, the pan and off the block it has no clearance because the differential is in the way. I removed half the diffential since the housing is split in the center. You will see bolts on the differential housing, remove those. But before the diff can come out to make room for the pan to drop you have to remove the axel attached to the diff on the passenger side. Once the axel is off the diff you have room to remove half the diff. Make sure to drain the gear oil first. It take a bit off pulling and wiggling but it will come off. Once that's clear the oil pan is completely free to come out. Hope this helps.

Apr 20, 2013 | 2002 GMC Yukon Denali

1 Answer

What releases the rear axels from the differential, to change the axel seals on the backer plate.96 yukon.

remove the pot cover and drain, remove the bolt that holds the center diff pin in, then remove pin,AT THIS POINT DO NOT TURN ANYTHING AXLES OR DIFF OR DRIVESHAFT push axle inward and remove u clip that holds shaft in then pull shaft out

Oct 29, 2010 | 1996 GMC Yukon

1 Answer

Ride control light is on

There are height sensor at each wheel attached to the frame and control arm and rear diff areas. The sensor can break off and the ride light will come on. If thats not the problem you will have to get the codes read.

Nov 05, 2009 | 2002 GMC Yukon Denali

1 Answer

I have a 2004 Yukon. I did not change the diff

Not unless you noticed an unusual amount of debris or dirt when you changed it at 86,000. If you want to shorten up the mileage between changes to get back on schedule then feel free, but you don't have to change it because you were late. If you are doing a lot of extreme driving, city or 4 wheeling you may want to shorten up the intervals. Hope this helps.

Nov 01, 2009 | 2004 GMC Yukon

1 Answer

Whinding noise from rear of 95 yukon

Have the pinion bearing in the rear diff checked.

Aug 28, 2009 | 1995 GMC Yukon

1 Answer

How do I remove the rear axles on my 2000 GMC Yukon XL so I can replace the tin brake liners in the wheel hubs?

well you need to pull rear cover and pull rotors or drums off and there are two clips in side the diff but you need to pull the center shaft out AND PUSH THE SHAFT IN WORD AND REMOVE TWO CLIPS AXLE WILL SLIDE OUT

Aug 13, 2009 | 2000 GMC Yukon XL

2 Answers

A hose that runs from the top of the rear axle has come off from the other end and it has this mounting plate. where dose it mount on the truck?

its a vent tube for the diff. mount it anywhere above the diff. as far as its original location, you will need a repair manual or look at another truck for an example. good luck.

Jul 17, 2009 | 1995 GMC Yukon

1 Answer

Determining which rear rotors needed

there is a metal tag on the cover of the differential that will say limited lip if u have it.

Jul 10, 2009 | 2001 GMC Yukon

1 Answer

2005 Yukon Front Diff Axle seals

You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
1995 GMC Yukon Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides