Question about 2008 Chevrolet Express

Open Question

Replacing a Sliding door handle in 08 chevy express

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2033 kia sedona sliding outer door handle

take inside door pannel of,gently remove plastic sheet,and you will see door handle,un clipdoor lever and nuts,

Posted on Jul 18, 2008

Ad
  • 26 Answers

SOURCE: Mazda 5 replacing external handle on sliding door

Your door should be held on with clips. Removing the panel is sometimes hard, just take a good WIDE flat head screwdriver, and whatever tool needed to remove the screws holding the panel on, and be careful. Check underneath the panel, by the inside handle, and the arm point for screws. Once removed, take your WIDE screw driver, and don't quite pry them off, more or less try to get it underneath and pull towards yourself. There is no real easy way, just try to be patient with it, and if you hit any binds, look for more screws, its just a matter of patience for sure.

Posted on Feb 14, 2009

michigan man
  • 3533 Answers

SOURCE: how do you reset power sliding door on 2000 chevy venture

there should be information in your owner manual telling you how to do it if you have miss place your owner manual try this website to see if you can down load one for your car its www.edmunds.com and i hope i was able to help you Michigan Man

Posted on May 12, 2009

  • 4369 Answers

SOURCE: Im looking for a sliding door handle for a 2000 nissan quest van.

ebay has them all the time also, go here for help on Quests http://autos.groups.yahoo.com/group/villagerquest/

Posted on Jun 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Chevy express van sliding door handle replacement


Check out Chilton's manual at the library - they will let you copy the pages you need in most cases. This is a problem you have to start by removing the inner panel and then you can get at it from behind the outside.

May 02, 2017 | Cars & Trucks

1 Answer

My right front door outside handle will not work on my 2008 chevy express


the rod conecting to the handle could have fell off, or handle where rod conects is broken

Feb 02, 2013 | 2008 Chevrolet Express Passenger

1 Answer

2008 chevy truck door not opening


how do u replace the cable on a 08 Chevy 2500 hd inside door handle

May 01, 2012 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Sliding door handle will open from inside but not the outside


the outside door handle connects to the lock by a metal bar and 2 plastic clips. One of your clips have broken. You can get the clips at any auto parts store. very easy to replace. just remove the door panel, and you will see the clips at the lock and handle. every thing just slips on and snaps in. hope this helps

Jan 13, 2011 | 2005 Chevrolet Express

1 Answer

I recently purchased a used 03 Chevy Venture van. The passenger sliding door doesn't open. It worked for 1 week and stopped. The driver side sliding door has a broken handle so I'm able to open that door...


Pain but fixable. Sounds like the linkage is not connected. Even a mechanic will have to remove the door panel and fight with it. If you can remove the rear seat from the drivers side side door then you might have room to remove the passenger side door panel to fix it. Usually clips are the first thing to break on door handle/latch linkages

Apr 06, 2010 | 2003 Chevrolet Venture Passanger

1 Answer

Broken door handle - 2001 Nissan Quest SE


first you van order parts at discount from tascafordparts.com.
quest & mecrury villager are the same vehicle made at the same assembly plant. good luck to all. If you were in detroit area, I wold help you.

Trim Panel —Sliding Door Removal
  1. Remove the sliding door trim panel finish panel.
532ac84.gif 2. Remove the sliding door trim panel 2965fbe.gif Latch Remote Control —Sliding Door Removal
  1. Remove the rear sliding door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. If equipped, disconnect the sliding door power door lock actuator electrical connector.
f373e91.gif
  1. NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.
  2. Disconnect the sliding door rear latch cable.
  3. Remove the bolt.
  4. Remove the sliding door rear latch cable adjusting bracket from the latch remote control.
  5. Disconnect the sliding door rear latch cable from the latch remote control.
b8f2f32.gif
  1. Remove the 4 sliding door front latch bolts.
NOTE: If necessary, transfer parts to the new sliding door latch remote control.
Remove the sliding door latch remote control.
  1. Remove the bolts.
  1. Remove the sliding door latch remote control.
cb5ee71.gif
Handle —Exterior, Sliding Door Removal
  1. Remove the sliding door latch remote control. For additional information, refer to Latch Remote Control—Sliding Door .
  1. Remove the sliding door exterior handle.
    1. Remove the nuts.
    1. Remove the sliding door exterior handle.
0c820f3.gif

Mar 08, 2009 | 2001 Nissan Quest

2 Answers

Mazda 5 replacing external handle on sliding door


Your door should be held on with clips. Removing the panel is sometimes hard, just take a good WIDE flat head screwdriver, and whatever tool needed to remove the screws holding the panel on, and be careful. Check underneath the panel, by the inside handle, and the arm point for screws. Once removed, take your WIDE screw driver, and don't quite pry them off, more or less try to get it underneath and pull towards yourself. There is no real easy way, just try to be patient with it, and if you hit any binds, look for more screws, its just a matter of patience for sure.

Feb 13, 2009 | 2006 Mazda 5

1 Answer

Side sliding door


The trick is that there is a small clip holding the inside handle in place. Push the panel in and grab it with small needle nose or forceps.

Then remove all the interior panels.

There are seven torx screws holding the intern latch into the door frame, and three interconnecting bars between the outer and inner inner handles.

Once you have the ability to move the inner assemble around you can get to the two metric nuts holding the exterior handle.

The lock assembly is removed by depressing the metal latch on the bottom of the handle assemble after the handle is fully removed.

Reverse and replace and that's it. (don't for get to have extra plastic door panel clips as they will break as you remove the interior panels)

Overall - I would suggest to just take it to the dealer or to a body shop. I'm told they would do it for about $75. I took about 2 hrs to do this and if you are even a bit shaky and drop anything into the door, it is game over. Next time I will do the dealer thing.





Oct 30, 2008 | 2003 Chevrolet Express

1 Answer

2033 kia sedona sliding outer door handle


take inside door pannel of,gently remove plastic sheet,and you will see door handle,un clipdoor lever and nuts,

Jul 12, 2008 | 2003 Kia Sedona

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

598 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...