Question about 2001 Ford Windstar

1 Answer

Looking for a diagram of the firing order of sparkplugs wiring on the coil and on the engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 667 Answers

1-4-2-5-3-6 is your firing order your cylinder layout is as follows:
(cyl #'s)
123
456
(front of vehicle)

on coil should be same as cyl #'s

Hope this helps, let me know.

Posted on Aug 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for dist firing order for 1967 430 plus a vacuum diagram and what side of coil does dist wire go on?


The firing order is, 1 8 4 3 6 5 7 2
Odd and even numbered cylinder banks. driver side bank, front to back, 1 3 5 7
passenger side bank, front to back, 2 4 6 8
Dist rotor rotation, clock wise.
If you put number one cylinder on tdc of compression stroke, then whichever sparkplug tower the rotor is leading into, in the proper direction is number one. Then you follow the firing order in proper direction around the cap.

Oct 14, 2017 | Buick Cars & Trucks

1 Answer

I change the sparkplugs and wire of mi mitsubishi eclipse 2003 but a think im doing wrong and im not put in order the wires did you have a diagram or wat i can do


hI,THEIR ARE TWO TYPES OF ENGINES FOR YOUR CAR,HERE'S A LINK TO THE 2.4 ENGINE FIRING ORDER. Specifications Firing Order AutoZone com HERE'S A LINK TO THE 3.0 FIRING ORDER. Specifications Firing Order AutoZone com WHEN CHANGING SPARK PLUGS AND WIRES,DO ONE AT A TIME SO YOU WANT GET THEM CROSSED UP.

Oct 05, 2015 | Mitsubishi Cars & Trucks

1 Answer

I change the engine on the car and it's bacfireing and hard to start with backfireing at all the time but it's runing it run fine


This sounds like a crossed sparkplug wire, start by making sure the firing order is correct, if theres a sparkplug wire in the wrong spot this would cause hard starting and the backfiring, so check the firing order first, i would of given you a firing order diagram but you forgot to list the year, make , model and the engine size. good luck and have a good day.

Mar 18, 2011 | Volvo XC70 Cars & Trucks

3 Answers

1999 ford escort I changed the plugs, but broke a plug cap. Bought a generic replacement spark plug wire that had to be modified to fit into the head. I cannot get the firing order correct. The car...


Remove the plugs from the head. Insert into the coil wires. Make sure they are properly earthed on the engine. Crank the motor and check for spark at each of the plugs.
Refer to the diagram. Cylinders are connected as shown on the diagram in blue. 1 goes to cylinder 1(sparkplug furthest from coil pack), 2 to 2, 3 to 3 and 4 to 4(closets to coil pack).
To test the coil pack use a digital volt meter. Measure resistance between coil towers for coil 1(marked 1 in red on diagram) Value should be between 12000 and 14500 ohm. Do the same for coil towers 2.
Measure resistance between I and C1. If the measurement is more than 5 ohm the coil is defective. Do the same for I to C2.
Measuring voltage at I(Ignition start/run) to ground should be 10V.
I is connected to the 15A engine fuse. The radio interference capacitor is connected between this line and earth at the coil. Disconnect it to see if it cures the problem.
C1 and C2 connect to the powertrain control module.
Bear in mind that aftermarket coil wires may cause problems with misfiring, so see if you cant find an OEM coil wire to replace the broken one before replacing anything else.

suzman_16.jpg

Nov 15, 2010 | 1989 Ford Escort

2 Answers

Replaced sparkplugs and sparkplug wires, now runs rough. I checked connections all tight. check firing orger, looks right. run good till I touched it. Help.


Check the firing order with the firing order diagram that I have uploaded, and if that does not solve the problem then remove the spark plugs and be certain that there is an even spark plug gap between all of the spark plugs, (see the emission label under the hood for the correct spark plug gap) and be certain that there is not any split-fire or multi-fire spark plugs installed in the engine, because those plugs will not work with an OBD-II system, and a random mis-fire is the least that they will cause if installed in an OBD-II controlled vehicle.


b4cb725.jpg

Aug 18, 2010 | 2001 Ford Taurus

2 Answers

Need to replace sparkplug wires.I had my plug wires ripped out of my car now I need to replace them in the right firing order.


The 3800 after 1984 is 'distributorless' so you have six "firing coils" located on the front of the engine and numbered for your convenience. looking at the 'front' of the engine which is where all the pulleys and the serpentine belt is viewing from the passenger side fender, the cylinders are numbered #1 on your right then #2 on your left and alternate right left from front to rear of the motor to connect your wires.

Nov 13, 2009 | 1996 Buick Park Avenue

2 Answers

Sparkplugs 1985 dodge ram


Do you mean you need a diagram for the spark plug wires? The firing order of the engine is usually molded into the factory intake manifold, and most distributor caps have the #1 cylinder location marked on it. For a more detailed look at it, try to find a repair manual for your truck.

Jun 26, 2009 | Cars & Trucks

1 Answer

Ignition wiring


firingorder6a.gif firingorder6.gif 1991-1994 2.9L and 3.0L Engines Firing Order 1-4-2-5-3-6 1995 And Later 3.0L V-6 With DIS Ignition System Firing Order 1-4-2-5-3-6
4.0L Engines Firing Order: 1-4-2-5-3-6 DIS Ignition System

Nov 22, 2008 | 1995 Ford Ranger Supercab

Not finding what you are looking for?
2001 Ford Windstar Logo

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...