Question about 1992 Plymouth Voyager

1 Answer

How do i remove radio for repair 1992 ply voyage

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

There is a plastic finishing plate that covers : the radio, two air vents, the cabin air controls, and a shelf. It is only pressed in. If you gently pull on the bottom edge it will start to pop out , gently work your way around and it will come off. Take off the two screws holding the cabin controls so you can move it. Undo the two screws holding in the radio and pull it forward. Unscrew the ground wire, unplug the antennae, and push the tabs on the multi-wire-plugs and pull them out. Feel around , but at this time you should be able to slide the radio all the way out.

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What hoses and lines hook up to radiator. What hooks up to part for toeing attached to radiator externally. 1992 Ply Van 3.3 L


I think you could use this manual method instead.. My nephew use it to repair my car and it's totally repaired now. Here's the website he bought it from. www.reliable-store.com
everything covered
wiring diagram/ electrical, error/fault codes
repair instructions
including removal, installation, assembly, parts info, pcv, service instructions
troubleshooting
engine issue
etc. a lot more

Jun 09, 2018 | Cars & Trucks

1 Answer

I have a 1992 ply voyager.it passed inspection,then the engine light stays on, now when i drive the van makes a loud jurking movement the stops and starts again. plse help.


You have an engine light on

So as with ALL Vehicle problems

You check for codes & resolve them first

Simply can't guess at vehicle problems without
a vehicle to drive & test

Apr 24, 2014 | 1992 Plymouth Voyager

2 Answers

Where is the ecm module located 92 ply voyager 3.3l


The 1992 Plymouth Truck Voyager 4WD 3.3L MFI 6cyl the Engine Control Computer is located under hood, driver side, front side of strut tower, rear of headlight, mounted on inner fenderwell .

Hope this helps (remember to rate this answer).

Jun 13, 2011 | 1992 Plymouth Voyager

1 Answer

I have a 98 ply grand voyager, and have heat from the drivers side vents, but cold air from the passenger side vents? please help


Does your van have seperate controls for driver and passenger temperature settings? If so the most likely cause is a broken actuator or broken passenger blend door. Unfortunately, the only way to repair a broken blend door is to remove the dash and the HVAC assembly.

Feb 05, 2011 | 1998 Plymouth Grand Voyager

1 Answer

I own a 1993 ply.grand voyager LE. My turn signals went out and I can't locate the bus fuse on the fuse panel. The repair manuel, repair shop owner and even the parts sales person swear its on the fuse...


you need to test the multi switch the harness connection is 3/4 down the steering column under dash --as to fuse and relay if hazards still work --on same fuse so not fuse

Nov 06, 2017 | 1993 Plymouth Grand Voyager

1 Answer

How do i change a leaking evaporator core.


the entire dash, door to door top to bottem has to be removed to be able to take out hvac housing so you can take apart to get at the core [recomend do heater core at same time] the dash comes out as an entire unit guages and all. bolts on ends under plastic covers,on top near winshield under vent trim.,bolts on floor in center below radio and a/c controlls,steering column has to come out. multiple wire connectors etc. its an all day job for a pro so its going to take awhile but its pretty straight forward

May 06, 2010 | 2000 Chrysler Grand Voyager

2 Answers

How do you remove pass rear wheel bearing on 99 ply grand voyager


the bearing has 4 bolts holding it on the inner side facing the axle. remove the wheel and brakes to get access to it

Mar 07, 2010 | 1999 Plymouth Voyager

1 Answer

1996 Ply Grand Voyager SE The blower motor


sounds like a faulty motor or relay

Oct 29, 2017 | 1996 Plymouth Voyager

1 Answer

How to remove radio from 1992 plymoth grand voyager


Pull on grille/trim it should be just snapped on there.

Jun 17, 2009 | 1992 Plymouth Voyager

Not finding what you are looking for?
1992 Plymouth Voyager Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

Marvin
Marvin

Level 3 Expert

81342 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...