Question about 2001 Volkswagen Beetle

1 Answer

How do i change the fog light myself? - 2001 Volkswagen Beetle

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volkswagen Master
  • 14,036 Answers

RAISE FRONT END OF VECHICLE.FROM BEHIND THE GRILLE AREA.GRASP THE BACK OF THE FOG LIGHT HOUSING AND TWIST IT COUNTER CLOCKWISE.PULL THE BLACK PLASTIC HOUSING AWAY FROM THE FOG LIGHT UNTIL YOU HAVE ACCESS TO THE METAL CLIP SECURRING THE BULBHOLDER.THEN REMOVE BULB INSTALL THE NEW BULB.PUT EVERYTHING BACK VISA VERSA.

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How hard is it to change a fog light bulb on a 2005 Subaru Forester? Can anyone do it?


Front Fog Light Assembly

REMOVAL


  1. Disconnect the ground cable from battery.
105919447



  1. Remove the two clips and lower mudguard on side that bulb is being changed.
  2. Disconnect the harness connector from bulb on back of fog lamp.
105919448




Front Fog Light Bulb

REMOVAL


1. Locate back cover on fog lamp assembly where bulb is located inside.

105919462



  1. Remove the back cover.
105919463



  1. Remove the spring retainer, and then detach the fog light bulb.
  2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.

Jul 27, 2011 | Subaru Forester Cars & Trucks

1 Answer

HOW DO YOU CHANGE THE BULBS OF THE FOG LIGHTS?


The fog lights on most vehicles sit directly underneath the headlight bulbs. The ballast and wiring work just like the headlights, so changing them takes not much time. The procedure to change the fog light is as follows:-- 1) Open the hood and reach down underneath the headlights to unplug the electrical plug from the fog light assembly. Squeeze the top of the release tab and pull the connection off the bulb's ballast. 2)Turn the fog light counterclockwise to remove it from the fog light housing. 3)Install the new fog light bulb.Then connect electrical plugs properly. 4) Test the fog lights by turning it ON. Thanks. you can rate this solution and show your appreciation.

May 20, 2010 | 2002 GMC Yukon XL

1 Answer

How do u change a bulb in the fog lights on a


The fog lights on most vehicles sit directly underneath the headlight bulbs. The ballast and wiring work just like the headlights, so changing them takes not much time. The procedure to change the fog light is as follows:-- 1) Open the hood and reach down underneath the headlights to unplug the electrical plug from the fog light assembly. Squeeze the top of the release tab and pull the connection off the bulb's ballast. 2)Turn the fog light counterclockwise to remove it from the fog light housing. 3)Install the new fog light bulb.Then connect electrical plugs properly. 4) Test the fog lights by turning it ON. Thanks. you can rate this solution and show your appreciation.

May 20, 2010 | 2003 Ford Focus

2 Answers

How do you change the headlight bulb on 1996 olds delta 88? I cannot get to the bulb assembly.



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Disconnect the negative battery cable.
  2. Remove the fog lamp-to-bumper assembly retaining screws. Be careful not to disturb the adjusting screw.



0900c152800b1fa2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the 2 Torx® fog light retaining screws (1), making sure not to disturb the adjusting screw (2)
  1. Squeeze the bulb and socket assembly retaining clip prongs inward, and pull the bulb and socket from the rear of the fog lamp.



0900c152800b1fa3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Squeeze the bulb and socket retaining clip prongs inward ...


0900c152800b1fa4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: ... then pull the bulb from the rear of the fog lamp
  1. Unplug the fog lamp electrical connector.



0900c152800b1fa5.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Unfasten the fog lamp electrical connector
  1. Install the assembly, retaining bolts and connect the negative battery cable.


AIMING

  1. Park the car on a level surface, at least 25 ft. (7.6m) from a wall that is perpendicular to the ground surface. Make sure there is no excess weight in the trunk, unless you normally travel with that amount of weight in the car. Bounce the car a few times to settle the suspension.
  2. Measure and record the distance from the ground to the center of each fog light lens.
  3. Turn the fog lights on and adjust so the hot-spots (lit area of most concentrated intensity) are 4 in. (10cm) below the height of the lenses. The ADJUSTING screw is located at the top right corner of the fog light.

Jan 25, 2010 | 1996 Oldsmobile 88

1 Answer

Change a fog light for a 2006 LR3


There is a circular cover surrounding the fog light assembly that simply pops off. Behind that cover there are three maybe four torx style screw that need to be removed, then simply just disconnect the electrical connector to the fog light assembly.

Oct 14, 2009 | 2006 Land Rover LR3

2 Answers

I want to install fog lights on my 1996 Chevy Cavalier. I am not quite sure about the wiring. I know I could do it myself with a little help from you guys or girls.


Depends on how you want to have them come on. On a switch you just control you would have the switch control a relay that is supplying power for the fog lamps. If you want them on all of the time find and ignition wire to conrol the relay for the lights.
The common thing in both of these systems is a relay. You must put one in the system. The fog lamps will draw to much amperage for a toggle switch.

Oct 11, 2009 | 1996 Chevrolet Cavalier

1 Answer

Changing fog light on a 2004 Kia Magentis EX V6


I believe you just need to reach up and under the bumper to disconnect the bulb and the harness

Aug 18, 2009 | 2005 Kia Sportage

1 Answer

How to change fog lights bulbs on my 2005 honda


548ae69.gif
  1. Remove the fog light mounting screw.
  2. Disconnect the connector from the fog light.
  3. Turn the socket about 45° counterclockwise and remove it from the housing.
  4. Remove the bulb from the socket.
To Install:
  1. Install the bulb in the socket without touching the glass with bare hands.
  2. Turn the socket about 45° clockwise to install it.
  3. Connect the connector to the fog light.
  4. Install the fog light mounting screw.

Jul 14, 2009 | 2005 Honda Odyssey

1 Answer

Fog lamp replacement on 2008 elantra


1. Disconnect the negative (-) battery terminal. 2. Remove the front side cover screw. 3. Remove the front fog lamp assembly connector (A).

38eda8f.gif 4. Remove the front fog lamp bulb (A).

20279ba.gif

Jun 20, 2009 | 2008 Hyundai Elantra

1 Answer

My fog light to my 2004 neon dodge does not work


there are no recalls on a 2004 neon

Jan 11, 2009 | 2004 Dodge Neon

Not finding what you are looking for?
2001 Volkswagen Beetle Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...