Question about 2005 Chrysler Town & Country

Open Question

How to replace oxygen sensor for 2005 town and country limited

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3600 Answers

SOURCE: oxygen sensor replacement

you need to rent an 02 sensor socket and use a ratchet and the socket to remove it, there are two on the exhaust pipe one before the cat, you can see it on the exhaust pipe and one after. normally the 1at one goes out. cost $75.00 please rate if helpful.

Posted on Aug 14, 2009

Testimonial: "it was very helpful! thanks"

Ad
short shadey
  • 421 Answers

SOURCE: location of the speed sensor on 1996 town & country

they are on the front drivers side of the transmisson and have two wires coming off them, there are two one is an input shaft sensor and the other is an output shaft sensor unless you have a 4 cyl van then there is only one sensor please rate -jeff

Posted on Sep 04, 2008

emissionwiz
  • 77201 Answers

SOURCE: i have a problem with power sliding doors on 2001 Chrysler Town and Country limited

do you mean they are sticking?

Posted on Oct 20, 2008

chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

  • 117 Answers

SOURCE: 2005 crank position sensor location

The crank shaft sensor on that model should be on the driver side towards the back of the tranny its not hard to get to.

Posted on Jun 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 town and country limited FWD 3.8 engine and got the following codes p0138 and p0032 i changed the oxygen sensors on the bottom and the oxygen sensor on the top next to the manifold and now i...


Code 138 was for bank one sensor two having a high reading. This is the sensor after the catalytic converter on the side with cylinder one.
Code 32 is for the heater circuit in the O2 sensor for bank one sensor one in front of the cat.
If you replaced both sensors on bank one and code 32 is coming back, there is a problem with the heater circuit going to the sensor.
The sensor uses a heater to heat up the exhaust gas while the engine is warming up.

Aug 09, 2012 | Chrysler Cars & Trucks

1 Answer

Crankshaft position sensor for 2005 chrysler town and country


when looking at the left hand side of the engine ( from the front or belt side ) it would usually be down on the block to the side of the crankshaft damper pulley and 4-5 inches back from the front of the engine.

Mar 08, 2012 | 2005 Chrysler Town & Country

1 Answer

P0032 Oxygen sensor heater problem. This is on a 2004 Chrysler Town and Country 3.8 L V6.


The sensor in question is behind the engine on the exhaust manifold.

You can test the heater in the sensor with an ohmmeter using the following procedure:
  1. Disconnect the electrical harness from the sensor.
  2. The white wires in the sensor connector are the power and ground circuits for the heater.
  3. Connect the ohmmeter test leads to the terminals of the white wires in the heated oxygen sensor connector.
  4. Check the resistance of the sensor, if it is not within 4-7 ohms, replace the sensor.
  5. ea87f67.gif

Oct 24, 2010 | 2004 Chrysler Town & Country

1 Answer

O2 sensor code po138 is it something a handy but not car savy person replace?


P0138 - O2 Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)
The Heated Oxygen Sensor (2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)

Symptoms: There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.


Causes: A code P0138 may mean that one or more of the following has happened:
  • Faulty O2 sensor
  • Short to battery voltage in O2 sensor signal circuit
  • High fuel pressure (not as likely)

Possible Solutions, here are some potential solutions:
  • Replace O2 sensor
  • Repair short to battery voltage in o2 sensor signal circuit

Hope help with this (remember comment and rates this).

Jul 22, 2010 | 2005 Chrysler Town & Country

2 Answers

I got the ABS Light on my 2005 Chrysler Town and


Stop at a Tuffy or other shop and they can scan for codes to tell you which sensor may be faulty. Wheel sensors are easy to replace.

Apr 09, 2010 | 2005 Chrysler Town & Country

1 Answer

05 town and country needs upper oxygen sensor. doe this need a trained mech or can i shade tree it


If you can get a wrench on it, there's no reason that you couldn't change it. Make sure you put anti-seize compound on the threads before installing new one, or you will never get it out again. Be aware: changing O2 sensor often does not fix a problem as exhaust content can be beyond sensors range and will cause false trigger, caused by another item in fuel system etc.

Oct 02, 2009 | 2005 Chrysler Town & Country

2 Answers

I need location of oxygen sensor on a 2001 town & country


ALL of your oxygen sensors are located i your exhaust system Your exhaust system starts at the exhaust manifold on the side of the engine and ends at the tail pipe by you back bumper. Your vehicle oxygen sensors are 4 of them there are two on each side of your exhaust the are actually screw into the exhaust they are like the nose of you engine to read how rich/lean the car is running. The are pretty simple to replace, they look kinda like spark plugs with wires attached to them the wires are usually colored white black and grey with plug connections on the end. To replace get a oxygen sensor socket and a ratchet and unscrew this socket can be bought at almost any auto parts place like auto-zone etc. Good luck and thanks for using FIX YA

Mar 22, 2009 | 2001 Chrysler Town & Country

Not finding what you are looking for?
2005 Chrysler Town & Country Logo

Related Topics:

377 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...