Question about 1999 Isuzu Trooper

1 Answer

How do i remove the rotor after removing calipar

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Isuzu Master
  • 450 Answers

Remove centre cap bolts, remove then circlip in centre, remove that section, then look for 3 philips head screws in "holey" lock ring and remove screws(sometimes need to do with impact driver), remove lock ring after undoing screws, then undo silver ring (anti-clockwise) by putting philips screw driver in holes of silver ring with lines in it and turning, then remove disc and hub as assembly (hub does separate if you undo the 17mm bolts that hold the disc to the hub, must do up this ring firm then back off and then do up the old feel method way. align a line in silver ring with top notch of centre threaded shaft that ring goes on, to one of the sides then when you put "holey" ring back on you can get the lock screws into silver ring.

Posted on Aug 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove rear rotor chiv 1 ton 2001

1-Remove the bolts from the center of the hub,
2-now pull the axle
3-remove brake calipar and mounting bracket
4-remove hub nut(this requirs a special socket)
5-now you can pull the hub and rotor

Jun 03, 2014 | 2001 Chevrolet Silverado 2500HD

1 Answer

Cant remove the calipar too change the brake pads on the front

You need to compress the calipar, sounds like a groove in the rotor, a big screw driver works

Aug 09, 2011 | Pontiac Grand Am Cars & Trucks

2 Answers

On a 1994 Chevy s10 pick up, how do you change the front brakes?

jack up frt end. remove wheels. take note of how the brakes go together. do 1 side at a time so you can use the other side as a referance. remove caliper bolts. use a c-clamp to push in caliper pistons. remove old pads. than remove caliper bracket and rotors.dont be afraid its not a big deal. make sure to check brake fluid level and pump the pedal when the job is completed.

Nov 19, 2010 | 1994 Chevrolet S-10

1 Answer

How easy is it to replace rear wheel bearings and seals in a 2006 odyssey?

first remove the wheel then remove the brake calipar held on by 2 14mm bolts, then remove the rotor, and then there are 4 bolts that hold the bearing on from the back side remove those and the bearing will come off

Dec 22, 2009 | 2006 Honda Odyssey

1 Answer

How do you remove the front rotors on a territory awd,does it require a 32mm deep well socket? The calipars have been removed.

If the calipers have been completely removed and the rotors don't just slip off, then the hub, bearing, and all have to come off.

Oct 31, 2009 | 2006 Ford Ranger

1 Answer

How do you remove the rear rotors from a 2007 Dodge Minivan?

Disc only!!! Remove rear tire. Remove 2 calipar bolts. Hang calipar. Don't leave hang loose. Slide rotor off. If stuck you must adjust the emer. brake, Going around the back side of the backing plate on the bottom. Remove the rubber boot. Using a brake tool or screwdriver adjust the star wheel adjuster to remove the rotor.

Oct 08, 2009 | 2007 Dodge Grand Caravan SXT Minivan

4 Answers

How do you remove the front rotors. I changed my pads but not the rotors. I saw a screw in the rotor with a philip head. I tried using my philip screw driver but it wouldn't turn I was only going to strip...

your rotors are only held on by your brake calipar and wheel when its on..they get rusted on remove wheel break calipar and the rotor should come off use a rubber mallet and beat on rear side and itll pop off.

Sep 23, 2009 | 2004 Land Rover Discovery

1 Answer

How do i remove the front rotors on a 2003 4x4 navigator. iremoved the calipars but the rotors will not come off. I there anything else holding them on the vehicle?

Proabably a large nut that goes through the center of the rotor to attach it to the axle. Are the studs for mounting the rims part of the rotor? If so, this is probably your best bet (you'll probably have to specially purchase this socket because it's going to be a 22+mm).

Jul 04, 2009 | Lincoln Navigator Cars & Trucks

2 Answers

Rear drivers side brake bleeder niple is froze - need to replace calipar - is this difficult? I have completed other repairs on brakes and replaced calipars before just not on a blazer

This is just like any other vehicle to change out the caliper. Almost all brakes are the same when it comes down to it. The only difference is the way certain companies either install them or the way they work. But on the Blazer it is really simple and can be done by just taking your time and doing it like you have done before

May 25, 2009 | 1998 Chevrolet Blazer

Not finding what you are looking for?
1999 Isuzu Trooper Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14423 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides