Question about Toyota Celica

Open Question

Cam timing marks on 94 toyota celica g.t. 2.2 engine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: head bolt torque specs and timing marcs for a 94 volvo 960 6cyl

you do 14 foot pounds then 45 foot pounds then a 120 degree turn.if aluminum heads are what you have

Posted on Nov 18, 2008

Ad
  • 11 Answers

SOURCE: timing marks for cam on 92 camry

on the intake cam use the middle mark in between the big one and the other small one on the exhaust cam use the use the smallest mark farthest away from the 2 small marks on the same tooth. line those 2 marks up on the same tooth in the middle.

Posted on Feb 11, 2009

jingB
  • 19 Answers

SOURCE: 1992 toyota celica 2.2 timing belt broke.i turned

well hold on there cowboy, first consult your service manual if your cars engine is an interference type. it means that if ever your timing belt breaks the valves that were stranded shall be hammered by up moving piston. eventually bending and warping of some of the valves would be a result. sometimes a damaged piston could also happen. timing belt breakage is a very serious matter and should not be taken likely. if you do not have a manual, what i do is removing the whole cyclinder head and inspect it. its better to be sure than sorry. in other cases you could see the warped valves by turning the crankshaft from tdc to 90 deg. and after which try turning the camshaft all the way around and carefully feeling the ease or difficulty in turning it and also the lift and rest of the rocker arms. any deviations you from the standard filler guage clearances would mean a bent or broken valves. hope this helps.

Posted on Apr 14, 2009

jagjeffery
  • 318 Answers

SOURCE: TIMING BELT MARKS DONT MATCH AFTER ENGINE TURNED OVER

dont worry about that you will have to turn the motor over 40 to 50 time before those timing belt marks line up again if your pulley marks line up correctly thats all you have to worry about

Posted on May 29, 2009

stevenhurc
  • 450 Answers

SOURCE: Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin

these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

Posted on Jun 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 94 toyota paseo, i've gotten the crankshaft notch on "0" and on the exaust cam, i have the 5E mark set up right, but i'm having a problem knowing how and where should my intake...


This is a single overhead cam engine, correct? Are you wondering about the other toothed pulley next to the crankshaft pulley? If thats the case then that pulley is the oil pump drive pulley and it has no timing marks. It doesn't matter how it is aligned when you put the belt on.

May 26, 2011 | Toyota Paseo Cars & Trucks

2 Answers

Still wont start, i have spark, airflow, and fuel


timing issue sound correct

pull off the front cover to verify cam/crank alignment marks?

when you say "new" engine do you me retail "new" or "new" for you

in other words, if you bought it second hand then you may have a NEW problem

Apr 28, 2010 | 2000 Toyota Celica

1 Answer

What is the timing specs for a 97 toyota celica 2.2 engine


Cylinder #1 at top dead center. Mark on the camshaft gear is straight up,as referenced to engine. Note that the engine tilts to the rear so reference the flat line of the head for 12'oclock positioning of cam timing mark.Distributor rotor points to #1 cylinder. If you have crankshaft pulley off, and can see the timing mark there, it should be straight down with #1 at TDC. After reassembly, start engine and jumper E1 and TE1 in the diagnostics box. This gives a smooth steady idle. Use timing light pointed at crankshaft pulley and hooked to #1 cylinder spark plug wire to check. Loosen distributor's 2 mounting bolts enough to turn it. Adjust as necessary. If you are having trouble seeing the notch on the crank pulley, get a white paint pen to increase it's visibility. Reference the rotating pulley mark to the stationary mark on the lower timing belt cover.

Mar 28, 2010 | 1997 Toyota Celica

1 Answer

How do you set the timing on a 94 Nissan Sentra?


There is 3 marks on the timing chain, 2 are exactly 16 links apart and the other is 22 from either of the 2. The engine should be at top dead center. Line the 2 (16 apart) marks with marks on your cam gears and the 3rd with your crank gear. Torque cam bearings to 100 inch lbs.

Feb 03, 2010 | 1994 Nissan Sentra 4-Door

1 Answer

Is my engine an interference engine?


If its a twin cam most likely.You can ask at Autozone or Oreilly auto parts.A Chilton or your owners manual will have the info on the timing belt change servicing

Oct 04, 2009 | 1991 Toyota Celica

1 Answer

Cant get no. 1 piston top dead center with the timing belt


Ive replaced the head gasket two times (two cars) with this engine, and had a little trouble with this. The mark on the intake camshaft that matches the mark where it connects to the distributer is tricky. The mark on the distributer connection is not supposed to match up square with the mark on the camshaft, if you do match them completely, then the teeth wont match up with the timing belt completely (#1 piston position) instead, the mark shows you which flat surface to allign if that makes since. The notch (dist side) is on a flat hex surface, it is not in the middle of the surface but it should be. as long as the two pieces hex sides are lined up, you should then be able to get good timing with the #1 position after turning the crankshaft to get the timing belt to line up. its hard to explain but all markings are right for the timing belt, but the distributer notch to line up the cams for timing is a little off. match the two surfaces (notch should me a few mm to the right of the other mark) Ive done this on 2 toyotas (87 celica and 89 camry) and they both work fine now. Hope this helps.

Apr 17, 2009 | 1990 Toyota Camry

1 Answer

94 celica starting problem


check your engine timing

Feb 16, 2009 | 2000 Toyota Celica

1 Answer

Replacing timing chain


didnt you make it before you took it off ??,piston no1 at tdc and valves on no1 closed and no 4 open ,TURN ENGINE 360DEGREES WITH A RATCHET BEFORE TRYING TO START ENGINE

Dec 16, 2008 | 2001 Toyota Celica

1 Answer

3.0 timing marks


the marks are correct and must be aligned ... loosen tensioner and try again...are you using old belt or new ?

Sep 27, 2008 | 1993 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...