Question about 1993 Ford Econoline

1 Answer

I need to install a new starter, I have purchased a starter for the 1993 ford model I just can figure out where the starter is actually placed under the hood of the van. Do you know where it is located?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 453 Answers

Should be located under van passengers side of motor

Posted on Aug 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace 1993 Ford Crown Victoria starter


The starter will be under the car on the passenger side. You will need to raise and support the vehicle. There will be two bolts that hold the starter onto the transmission. Remove those two bolts and lower the starter. You can then remove the positive cable end and the smaller start terminal wire. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 26, 2012 | 1993 Ford Crown Victoria

1 Answer

How do I remove the starter motor from a 1993 Ford Fairlane?


  • Use a wrench to loosen the bolt and nut assembly that secures the negative battery cable to the battery, then lift the cable away from the battery.
  • 2 Apply the parking brake and raise the front of the car with a jack, then lower the vehicle onto two jack stands. Place one jack stand on each side of the front of the vehicle, under the frame.
  • 3 Access the starter from underneath the passenger's side of the Falcon. The starter is between the engine and the transmission and looks like a large coffee can.
  • 4 Remove the battery cable from the side of the starter. The cable slides over a threaded stud and is secured with a single nut. Remove the nut with a wrench, then lift the cable away from the starter.
  • 5 Remove the two flywheel-to-starter retaining bolts with a wrench, then pull the starter toward the front of the vehicle to remove it.
  • 6 Position the replacement starter against the flywheel housing, then install and tighten the two flywheel-to-starter retaining bolts with a wrench.
  • 7 Slide the battery cable onto the threaded stud on the side of the starter, then install and tighten the retaining nut with a wrench to secure the cable in place.
  • 8 Lift the vehicle with the floor jack, remove the jack stands, and lower the Falcon to the ground.
  • 9 Position the negative battery cable onto the battery terminal, then tighten the cable into place with a wrench.
  • Apr 28, 2011 | Ford Fairmont Cars & Trucks

    1 Answer

    Starter location ?, 2002 sedan, installed new battery, won't start, I figure the starter may need a tap. It 'sometimes' clicks, but no engagement.


    hello, most Hyundai starters are located at the front of the engine (radiator side) below and behind the exhaust manifold, accessability to the starter is from under the vehicle and is held in place by two 14mm bolts and may also have a heat sheild covering the starter.

    Mar 29, 2011 | Hyundai Elantra Cars & Trucks

    1 Answer

    My 1993 ford tempo will not start because the distributor rotor is not in the correct place. I figured out the correct firing order but not the positioning of the rotor. What is the correct positioning of...


    The rotors for most cars have a guide groove or have a guide inside the rotor. If they don't they will rotate on the shaft and you would lose timing. Check your rotor and see if the guide is broken off. If this is the problem you need to buy a new rotor.

    Sep 21, 2010 | 1993 Ford Tempo

    1 Answer

    How to change a starter motor


    Disconnect battery, remove and mark wires and cable taken off starter, remove the 3 mounting bolts and remove starter. It looks like two bolts come from other side and bolt into starter and 1 bolt goes thru the starter into the bell housing/motor. Do the oposite to install. Here is a picture of your starter and a good place to purchase it. Wish you luck.

    http://www.partsgeek.com/catalog/1993/ford/festiva/engine_electrical/starter.html

    Jan 25, 2010 | 1993 Ford Festiva

    1 Answer

    DESCRIBE HOW TO REMOVE A STARTER FROM A 93 FORD TEMPO


    First disconnect the battery. After that, find the starter (should be bottom right). Remove the wires from the starter making sure you remember where they go. Remove the two bolts that hold it in place (one on top, one on bottom). Reverse all of this to put the new one in.

    Oct 24, 2009 | 1993 Ford Tempo

    1 Answer

    93 Ford Explorer Starter won't disengage from Fly Wheel


    My ford f150 did the same thing, so I put the old starter solenoid back in( the one by the battery) and it cured the problem.
    Come to find out, the after market relays aren't rated right, to get a good one, and the right one, you have to spend more and get it at a dealer.

    Aug 18, 2009 | 1993 Ford Explorer Limited

    2 Answers

    Locating the starter in a 1993 ford explorer


    it will be bolted around the bellhousing /gearbox area ,try a good battery off of another car first no jump leads .a battery may appear good with volts and all that but reserve amperage to turn the engine over is another matter

    Jun 29, 2009 | 1993 Ford Explorer Limited

    1 Answer

    1993 Ford Escort


    this is a common problem because the ignition switc gets ;oose and in the process could have grounded under the steering column so just repair the wires to the starter motor and instal the new ign switch and you may end up replacing the starter motor also

    Oct 03, 2008 | 1993 Ford Escort 4 Door

    2 Answers

    Ford 1993 probe horn


    The horn Button at the steering wheel is simply a switch. It grounds out when pushed causing the circuit to close, routing it though the actual  horn under the hood which is sitting there waiting to activate.

    Jul 24, 2008 | 1993 Ford Probe

    Not finding what you are looking for?
    1993 Ford Econoline Logo

    Related Topics:

    153 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5522 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...