Question about 2000 Pontiac Grand Prix

1 Answer

How do i change the front wheel bearings on my 2000 Pontiac Grand Prix GT?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Pontiac Master
  • 76,846 Answers

Front Wheel Hub Bearing Replacement Here is a great set of instructions for the installation of a GM front wheel hub bearing assembly. One of our customers submitted this for us to show to the public. Hopefully anyone thinking about tackling this job will find these helpful. Removal
1. Remove hub cap/dust cover.
Tip: If you do not have an impact wrench (air operated gun), you may want to remove the center axle nut at this point. Removing this nut with the wheel still on and before jacking up the vehicle, will make it much easier and give you enough leverage to get it loose with a regular ratchet or breaker bar (recommended). You may have access to the axle nut without removing the wheel. If you do not have access, you can remove the wheel and put the spare tire/wheel on. The spare wheel has a very large center hole and gives you access to the center axle nut. With the vehicle back on the ground, you can put the breaker bar with the proper size axle nut socket, on the nut and loosen it. Then jack up the vehicle and remove the wheel. 2. Jack up vehicle and support properly. **We know you know, but be very careful. You should always put a jack stand under the vehicle and use that to supprt the vehicle, not the jack. Also you should also use wheel ckocks to prevent the vehicle from accidentally rolling. If you are doing do-it-yourself repairs often, it is wise to buy good quality tools and equipment. This can help get the job done quicker and certainly safer. 3. Remove lug nuts using 19mm socket. Remove wheel and set aside. 4. Remove 2 caliper mounting bolts using a 15mm socket. Set caliper aside. Do not let it hang from rubber brake hose. 5. Remove 2 caliper mount bolts using 15mm socket Set caliper mount aside. 6. Remove brake rotor by sliding it off and set aside. NOTE: If the brake rotor has never been removed, their may be 2 small screws or retainers holding it in place. Remove these and the rotor will slide off. If it is stuck, you can lightly tap it with a hammer. 7. Remove 3 hub mounting bolts using 13mm socket. These are located on the inside of the steering knuckle next to the outer CV boot. A 3/8's drive ratchet with swivel and extension is best for this. Also if you are having trouble, look closely at how you have it jacked up. You may be able to reposition the jack and change the angle of the axle. If you have it jacked up under the control arm, you still have the suspension compressed. If you jacked it up by the frame rail, the suspension is opened up and may give you a better angle. Again be very careful with the jack and always use a jack stand for support. You can always use more then one jack stand to help as a safety also. 8. Remove axle nut using 1 5/16′ or 34mm socket. 9. Unhook and then unplug the ABS sensor. 10. Remove hub assembly. Be careful to make sure the axle splines are free from the hub. Once you have the axle nut off you should be able to push the axle in towards the engine with the bottom of the palm of your hand. If it is stuck, you can rethread the axle nut 1-2 threads, then place the socket back on and tap it with a hammer. This is mainly to assure the axle does nte get pulled out while pulling off the hub. The hub may also require a slight tap with a hammer or very rarely a puller to get the hub loose. Hit the hub and pry with a screwdriver or small prybar until hub comes out. (Most Auto Zone or Advance Auto Parts stores will allow you to borrow a puller if needed.) 11. Clean mounting area with a wire brush so new hub slides on easily. Make sure there is no rust or material that may cause the hub to not sit flush. 12. Install new hub assembly. 13. Use thread locker on the 3, 13mm mounting bolts and tighten. **GM recommends replacing these bolts every time they are removed. This is because the torque can be affected by re-using the bolts. The threads stretch when the are originally installed/removed and they can never really be torqued properly again. Also it is strongly recommended to replace the axle nut for the same reason** 14. Hook up the new sensor plug. 15. Install the axle nut using a 1 5/16′ or 34mm socket. VERY IMPORTANT!!! Do not over torque or under torque this nut. Also it is strongly recommended to never use an impact wrench to tighten this nut. Please tighten with a torque wrench to 118 ft. Lbs.(Other year and model vehicle torques specs may differ, please email us if you would like to know yours. Over or under torqueing this nut is the number one cause of premature bearing failure!!!!!!( It is also recommended to replace this nut as the threads will usually be stretched from being installed and removed. Threads will be stretched if installed with an impact wrench and also the bearing will be squeezed excessively which will cause premature failure. 16. Slide on the brake rotor. 17. Use a tiny bit of thread locker on the 2, 15mm caliper mount bolts and tighten. 18. Install the caliper mount bolts using a 15mm socket. 19. Install the wheel using a 19mm socket (Torque lug nuts with torque wrench to 100 Ft. Lbs.) and press hub dust cover into place.

Posted on Aug 04, 2010

  • yadayada
    yadayada Aug 04, 2010

    here is the part number and picture of hub assbly



    SKF Part # BR930548K {#10305030, 12413093, 12429204, 12429205, 88964168, 89047684}
    4-Wheel ABS; Front




×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wheel bearing torque spec for a 2006 Pontiac grand prix gt on the front wheel bearing hub assemnbly


It shouldnt have torque spec more of press preference to press the bearing in
the bolt should be put on with codder pin to follow

May 17, 2014 | Cars & Trucks

1 Answer

Front wheel makes noise


At low speed move steering wheel from left to right gently if the noise disappear or the sound change ,,,,you have a wheel bearing defect
hope it helps

Mar 27, 2014 | 2000 Pontiac Grand Am GT

1 Answer

2000 Pontiac Grand Prix GT, front end shakes at 35-40mph?


You have worn front end parts or the tires have a separated cord in them.

Feb 28, 2017 | 2000 Pontiac Grand Prix GT

1 Answer

Traction light on


Traction light is part of the ABS brake system. I had to the same problem 2 years ago and my auto repair guy said it was my front hub bearing. I replaced both sides with new hub bearing (right & left wheel) and now I have to replace the left one again. The thing about 04 grand prix gt they have a wheel/hub bearing problems. GM never recalled for this problem

Jun 19, 2012 | 2004 Pontiac Grand Prix

1 Answer

My ABS, traction control, and steering assist lights are on in my 2004 pontiac grand prix gt. The rear wheel bearing assembly was just replaced. what would cause this?


Hi, the wheel speed sensor and tone ring are built into the bearing/hub assembly. Make sure the new hub contains an ABS wheel sensor and the cable was properly connected. If it is properly connected, the new hub may be defective.

Apr 19, 2011 | 2004 Pontiac Grand Prix

1 Answer

Whirring noise when in drive


more likely a wheel bearing jack up each wheel and check for play,

May 24, 2010 | 2000 Pontiac Grand Prix

1 Answer

About how much should it cost to replace the


If you do it yourself about $50-$70.depending on where you buy the parts. but if your taking it to a shop ask how much they charge for labor and how long it will take. try a few different place some cost less than others. however it should not take anymore than an hour and a half.

Dec 11, 2009 | 2000 Pontiac Grand Prix

1 Answer

Wheel bearing torque


Front:
Mounting bolts 96 ft/lbs
Axle nut 159 ft/lbs

Rear:
Mounting bolts 55 ft/lbs

Sep 26, 2009 | 2001 Pontiac Grand Prix

Not finding what you are looking for?
2000 Pontiac Grand Prix Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...