Question about Dodge Ram 1500

1 Answer

Well it goes to floor i replaced clutch slave cylinder last night worked perfect this morning nothing again i got a 1998 dodge ram 1500 5 speeed

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 115 Answers

Look under the drivers side dash and see if there is fluid dripping down fire wall where the clutch rod goes to master cyl.possable leak at master cyl.is the fluid low

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ford Bantam 1.3 Clutch pedal goes to floor. Master cylinder pot full....


obviously your master is leaking on just plain worn out. or there is a system leak someplace

May 03, 2018 | Ford Cars & Trucks

1 Answer

Hydraulic clutch


change the seals in your slave cylinder.

Dec 07, 2013 | Dodge Neon Cars & Trucks

1 Answer

04 f350 when the truck sits over night the clutch pedal goes all the way to the floor with no presure you can pump it a few times and it works after it sits again back on the floor?


You have a leak in the hydraulic clutch system, most likely it is the slave cylinder down on the bell housing that is the problem as it is exposed to the most heat stress and wear and tear. The slave is part of the clutch release bearing and that means the transmission must be removed to replace it.

Nov 06, 2012 | Cars & Trucks

1 Answer

Clutch pedal has no pressure and goes straight to the floor when pressed. clutch disk is in good condition. parked the car the night before was working perfect. next morning no pressure and out of fluid....


Pump the clutch pedal and then check for leaks again, including under the dash where the rod from the pedal goes into the clutch master cylinder. Once you find the leak, replace what's leaking and bleed the system to restore the pressure (bleeds from the slave unit, just like bleeding brakes)

May 30, 2011 | 1996 Honda Civic

2 Answers

Clutch went to floor tis morning,puddle under truck. put fluid in still nothing,come home from work get in push clutch and its perfect?whats up here?


You probably have a bad master cylinder, slave cylinder or hole in the line. I am guessing that while you were gone the air in the system worked its way out. Find the leak and blead the system then you should be good to go.

Sep 21, 2010 | 1996 Chevrolet Blazer

2 Answers

Clutch goes to floor


There are four main things that can go wrong in a hydraulic clutch system, causing this condition. In order of DIY-friendliness: 1. Just bleed the system could be enough provided there are no significant leaks. Check out this for a procedure suggestion: http://www.motorvate.ca/mvp.php/803 2. Check for leaking hoses, tubes and connection in this hydraulic circuit. Rust could be an issue, also cracking old hydraulic hoses. Not that hard to replace faulty components usually but it depends. 3. The main cylinder for the clutch system is leaking and needs to be replaced. Don't know how hard it is on your car but this is mostly a rather painless procedure. 4. The slave cylinder is leaking. On some cars it can be a real pain to replace as you have to take the transmission out, no fun at all on Saab 9000 for instance. On other cars the slave cylinder is more accessible and rather easy to replace. You should not drive this car at all until you at least made step 1 here, bleeding the system making sure it works. The car is basically inoperable without clutch. If the problem comes back, you have to proceed through the steps until you find and correct the problem. Good luck!

Jun 04, 2009 | 2000 Nissan Maxima

1 Answer

2007 dodge truck 1500 4x4 4.7L clutch will not release?


check the pump in clutch pedal for loss of pressure

Jul 09, 2017 | 2007 Dodge Ram Truck

1 Answer

1998 dodge 1500 wont shift


first of all standard or auto i am guessing its standed standard under drivers side hood near master cylinder there is a small clutch reservoir if there isnt enough fluid it wont extend the throw out bearing far enough for a shift because the clutch pedal is hitting the floor not enough fluid to extend the slave cylinder to drive the fork second faulty slave cylinder or throw out bearing as far as the light blown dash bulb or somone snipped the wire or took the bulb out

Sep 11, 2008 | 1998 Dodge Ram 1500 4WD

1 Answer

Clutch problem,where is the slave cylinder located


The clutch slave cylinder is located on the left side of the transmission, but i believe that the slave cylinder may come with the master cylinder and lines already attached

I’m happy to assist further over the phone at https://www.6ya.com/expert/jonathan_3a3c556b4b17d1d2

Aug 20, 2008 | 1996 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...