Question about 2003 Hyundai Santa Fe

2 Answers

Hazards and flashers aren't working - 2003 Hyundai Santa Fe

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 676 Answers

When you turn on hazards and flashers, do the lights at least come on. First check fuses be sure that they are good. Then check for the flasher relay. The flasher relay will usually be near the driver kick panel. I believe in this vehicle it will be a three prong relay. Good Luck.

Posted on Aug 04, 2010

  • Chris Bulldog Oct 27, 2010

    Why did you say it will probably be a three prong relay? What else would it be? Two? Why would one be two and one be three? Does a three prong do more than one thing, such as being a flasher for both the hazards and the turn signals? Instead of one for each? Let me know please!?

  • Chris Sellon Jul 10, 2012

    what if you turn the signals and they dont work but dont blow a fuse, then when you hit the hazzard switch the fuse blows? would it be the switch or the relay?

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 8 Answers

I have a 2004 Hyundai Santa Fe.By me the hazard and blinker lights would work sometimes then not work at all.The flasher is to the left of the fuse box, very hard to get to, you need to get on your knees, i had to pull out both blue relay switches from the bottom of the fuse box to get to it,don`t worry the blue relay switches can only go back in only one direction if it doesn`t line up, rotate the blue relay switches untill they line up then push in gently till they are snug , i took a flashlight and saw the flasher, there is a clip on top and on bottom of the flasher that need to be pressed to release it, i did one at a time because both of them are hard to squeeze at the same time,once the clips are released pull out the flasher it is a 3 prong flasher and can only be inserted one way, i also removed the dash panel, there are 3 screws that hold it in place,pull on it but be careful there are clips holding it in place that can break.The rotate knob might hang loose after you pull the dash just make sure you put it back.The raised lettering goes to the right when inserting it,don`t get upset it will fall a few times you need both hands to reinsert it hope this helps Jay

95550-39000
12v 85C/M
T/SIG(W)
32(28)+27+1.2
21X2+5+1.2
HAZARD(W)
(32(28)+27+1.2)X2+1.2
(21X2+5+1.2)X2

Hazards and flashers aren't working - hazards-flashers-arent-working-dcb1gui1noyzdjedu5q5jft1-2-0.jpg



hazards-flashers-arent-working-dcb1gui1noyzdjedu5q5jft1-2-5.jpg

Hazards and flashers aren't working - hazards-flashers-arent-working-dcb1gui1noyzdjedu5q5jft1-2-9.jpgent-working-dcb1gui1noyzdjedu5q5jft1-2-9.jpg" alt="hazards-flashers-arent-working-dcb1gui1noyzdjedu5q5jftHazards and flashers aren't working - hazards-flashers-arent-working-dcb1gui1noyzdjedu5q5jft1-2-14.jpgt/uploads/images/hazards-flashers-arent-working-dcb1gui1noyzdjedu5q5jft1-2-14.jpg" alt="hazards-flashers-arent-working-dcb1gui1noyzdjedu5q5jft1-2-14.jpg" class="h_mi" />

Posted on Jul 10, 2015

  • Sarah Dupont
    Sarah Dupont Nov 10, 2015

    How do you check the turn signal relay after locating and removing it? It's not like a fuse where you can see it's broken right? I replaced my battery (because the old one literally just died and was not coming back with a jump) and, after doing so, I have no turn signals or hazards (and a couple other not-super-important right now things like power to sunroof, clock, etc). I had a few blown fuses in the interior fuse box and decided to replace all fuses in that box (all looked corroded and what not). Still no TSigs or hazards.. The blinkers and hazards appear on my interior dash like normal, except blink super super fast. They just don't show on the outside of the vehicle. All bulbs are good, as well. I think checking the relay would be the next step? And if not the relay then....? A shortage somewhere? Since the items in question have no direct relation (i.e. Sunroof, clock, signals, hazards), and the fuses are all replaced, I think it could be the relays and/or multiple shortages? Any thoughts or help would be GREATLY appreciated, as I am trying NOT to spend a fortune of diagnosis at a shop unless absolutely necessary b/c of much $$ I spent on having to get towed out of the middle of nowhere, new battery, etc. TIA :)

×

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 76164 Answers

SOURCE: turn signal

The turn and 4 way are seperate, turn on the 4 way and follow the sound, it will be near the steering column.

Posted on Sep 21, 2008

  • 40 Answers

SOURCE: turn signal and hazards wont work

Do you have a trailer wiring harness? If you do, recheck the wiring there. If that doesn't help and you have properly checked the flashers then you need to check each bulb

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can,t get signal or flashers to work on 1997 Dodge Intrepid


I assume you've checked the Fuses :p Obviously that hasnt worked and the bulbs and lights haven't worked either... SO try this????
Open the driver's side door and examine the end of the dash for an access panel. Behind the access panel are fuses and flashers. There are two flashers inside the access panel for controlling the turn signal and the hazard lights. You can distinguish them apart from each other by turning on the hazards or the turn signal and feeling for the clicking. If you turned on the hazards, then the flasher that is clicking is the hazard flasher.
Remove the turn signal flasher from the dash and reinstall the new flasher into the vacated slot in the dash. Close the access panel and start thetruck . Check the turn signals for proper operation and make sure the hazards work as well.


Please let me know how it goes
  • Jan 07, 2012 | Cars & Trucks

    1 Answer

    Hazard/turn signal dont work 2002 monte carlo will not fash nor turn on once in a while indicator light blink for a slight second


    you could have a bad flasher unit causing this.you say hazard/flasher not working.do you mean just the signals not working and think the hazards won`t work or are the hazards not working.there are two flasher units one for signal and one for hazards.you could have a problem with the signal switch as well.

    Jul 05, 2011 | 2004 Chevrolet Impala

    1 Answer

    I bought a 1995 truck and the brake lights aren't working I noticed ythat the hazzard light switch is busted up could that be the source of my problem


    Check the fuses. And check for power at the taillights (These taillights have circuit boards on the back side that can go bad.) I don't think the hazard switch is it because the brakes would still work. Also check the brake pedal switch. There is a hazard flasher, does the hazards work?

    Jun 06, 2011 | Chevrolet C1500 Cars & Trucks

    1 Answer

    My 2000 cavalier signal lights stopped working all together....both directions. the hazards still work, but i cant get my left and right turn signals to work.


    Probably the flasher, as I think you have a separate flasher for the turn signals under the dash above the brake pedal. It is probably next to the hazard flasher. If you can't find it, turn the hazards on and follow the sound. The turn flasher is probably next to the hazard flasher. Please let me know if this isn't the problem or you have more questions.

    Dec 17, 2010 | 2001 Chevrolet Cavalier

    3 Answers

    My turn signals on my 87 camaro don't work but hazards do.anyone know the problem?


    Most likely it is a defective turn signal flasher......put in a electronic unit when changing it.

    Oct 29, 2009 | 1987 Chevrolet Camaro

    1 Answer

    Grand cherokee 2001 flashers dont work but hazards do...v odd??


    The hazards and the flashers are on seperate circuits.When the flashers are working properly you will hear a clicking during operation.If not,check all the bulbs.If both flashers don't work it may be a blown fuse,faulty flasher unit or a loose wire or connection.Probably the flasher unit.Make sure the new one is the same as the old one by comparing the two,On yours,its a combination flasher and hazard unit.It will need to be replaced.its small and cost is minimal.When you do replace the unit,disconnect the neg. cable from the battery.The unit relay may be blue in color.Hope this helps

    Sep 12, 2009 | 2001 Jeep Grand Cherokee

    1 Answer

    My hazards in my 1997 camaro rs work, but the back and front turn signals dont. The lights for the signals dont work in the dash either, just the lights for the hazards


    check the signal flasher ( little silver or colored can in fuse panel or under dash. 4 ways have 1 flasher and the signals have a seperate flasher. Put hazards on to hear click, to determine which flasher is which. Hope this helps

    Apr 13, 2009 | 1997 Chevrolet Camaro

    1 Answer

    Hazards work turn signals dont


    check your flasher the Hazards have a seperate flasher its a littl cube that looks like a relay in or near the fuse box

    Apr 07, 2009 | 1987 Pontiac Firebird

    Not finding what you are looking for?
    2003 Hyundai Santa Fe Logo

    511 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...