Question about 1999 Buick Century

1 Answer

How do i remove my steering wheel? I took out all the bolts buts its still on there, if anyone knows it would be much appreciated!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

After removing the center nut from the shaft that goes through the center of the steering wheel, you will need a steering wheel remover tool (steering wheel puller) most auto parts rent this tool.Also on the steering wheel and the shaft each will have a line mark that both meet, when installing steering wheel bad on, make sure that the marks meet or steering wheel will not be center.Hope this was very helpful.

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CAN YOU TELL ME HOW TO REMOVE THE STEERING WHEEL ON MY TRUCK


you have to pop the airbag out and then there is a bolt that bolts the steering wheel to the steering shaft take it off and then get a steering wheel puller and pull it off

May 28, 2012 | Ford F-250 Cars & Trucks

1 Answer

On my second steering colum know and this one about the same problem with last one the steering wheel is real wobbly and the key switch gets stuck cant start or shut off wich ever both. is this a hard fix...


These steering columns are not all that hard to work on. You will need a steering wheel remover, then a lock plate remover (can rent for free at autozone), that is the piece under the steering wheel. Once you remove these pieces you can access the 3 torx screws that hold the upper part of the column tight to the bottom of the column. You will need to use loctite on these bolts!

Jul 03, 2011 | GMC Sierra Cars & Trucks

1 Answer

We are having a problem with the steering wheel moving around..hubby took it apart and thought it maybe the lever that makes the wheel go up and down, but that is not the case..any ideas?


He will have to remove the steering wheel and the turn signal switch, with a 1/4" extension about 6" long and a 5/16 socket 13 point there will be three small bolt that you can see from the top those bolt's just came loose, hope this was very helpful.

May 18, 2010 | 1991 Chevrolet C1500

1 Answer

I need to know how to take off a steering wheel from a 2002 chevy pick up truck


1 remove negative battery cable 2 remove air bag module from steering wheel, this is usually bolted thru from the back of the steering wheel 3 remove steering wheel retaining nut. 4 Using a steering wheel puller pull steering wheel from steering shaft.

Mar 16, 2010 | 2002 Chevrolet Silverado

1 Answer

Ignition tumbler removal


There is a metal button on the ignition housing. Insert your key press the button while turning the key until the button goes in pull out the tumbler. Let me know if the helps. You need more help I will sent you step by step instructions. Hope that helped u out.

Jul 01, 2009 | 1997 Jeep Tj

3 Answers

My steering wheel on my van is loose


I think the problem you have is the steering assembly being loose.

To repair this, you must remove the steering wheel and work slowly down the column assembly, removing the indicator switch, ignition switch and other assorted springs and things. Lay out the removed parts in the order and orientation you remove them, take digital pictures or draw sketches at all stages, watch the spring placements. I also unplug the column looms to give you more room by moving the switches away for the area in the column where you are working.

Once you get far enough down the column you will see the three bolts that are loose, hidden in a sub assembly. I have only been able to tighten two of these over the years. This is a common fault.

Rebuild the column using the reverse of the order you removed it.

Good luck

Apr 11, 2009 | 1991 Chevrolet Astro Extended

1 Answer

Wobbly tilt wheel


Remove horn pad . After removing the large nut SCRIBE A LINE ON THE CENTER SHAFT and the STEERING WHEEL, Using a steering wheel puller, remove steering wheel. Now comes the tricky part. Remove signal stalk ( just pull out a couple of inches ),and 4-way flasher knob. Disconnect multiple connector of signal switch. Remove 3 screws holing switch down. Gently pull upward on switch to expose lower steering bowl. The large bolts are LOOSE that secure it, so the reason for the wobble. Tighten bolts, and reverse procedure.

Mar 31, 2009 | Oldsmobile 88 Cars & Trucks

1 Answer

Buick ignition cylinder stuck


What you do is disconnect the battery as to not set off the airbag, and then remove the steering wheel. This will allow you access to the retaining bolt, should be a torx 20 or 25. Pull the bolt out and the ignition will slide right out of the hole, like you are pulling the key out. Then unplug it and replace. Reinstallation is reverse of removal.

Mar 08, 2009 | 1994 Buick Skylark

1 Answer

Remove me Steering wheel bmw 1999 e46 3 series


Disconnect negative battery cable. Locate airbag retentions on back of steering wheel. Unbolt or unclip retention devices, and release airbag. Then: Unplug airbag electrical connector. Remove nut or bolt in center of steering wheel with pneumatic impact wrench if necessary . Using appropriate steering wheel removal tool kit, carefully remove steering wheel, paying attention to associated wires, etc. Unplug anything not accompanying wheel, or that is in the way. Pay close attention to any rods, or contact pieces associated with the horn button(s.) Replace these upon reinstall. Reverse order to install including tightening center bolt to 35-55 ft-lbs. If this is your first stg wheel removal, try an old chevy, preferrably someone else's! If inexperienced, don't risk bruising your favorite Bimmer!!! Hope this helps you make your decision. Tater Todd

Jan 28, 2009 | 1999 BMW 318 ti

Not finding what you are looking for?
1999 Buick Century Logo

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...