Question about 2008 Pontiac G6 Sedan

Open Question

How to change the brake pads on a 2008 pontiac g6

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: rear brake pads

try going to the site below here as well as reading this, it's really helpful and informative, it's a nice step by step. braking systems, when it comes to changing the brake pads hasn't really changed much with modern technology, just remember to used the proper tools to compress all the pistons equally, and also if your pistons have that cross going over the top of them then you have to use a pair of needle nosed pliers to turn the piston counterclockwise this will compress the piston.....hope this and the site are helpful....good luck and happy wrench turning!

http://www.edmunds.com/ownership/howto/articles/43787/article.html

Posted on Jan 28, 2009

Ad
  • 1 Answer

SOURCE: can not compress the rear

you can't use a c-clamp to compress the rear calipers. just as adidas_153 said you need a special tool that you can rent from Autozone for a $30 deposit.

Posted on Feb 22, 2009

  • 1 Answer

SOURCE: how to remove door panel 2008 pontiac g6

2008 g6 sedan i want to remove drivers door panel?Curt.

Posted on Mar 29, 2009

  • 179 Answers

SOURCE: how do i change the headlight on a 2005 pontiac g6

its probally a haligen bulb needs replaced from the inside under the hood that twists in the back of the light just half a turn the unplug old and put in new

Posted on May 31, 2009

  • 11 Answers

SOURCE: changing rear brakes on 2006 pontiac G6 how do i

Ok! here is the solution ...
After changing the pad dont try to push back the piston the old fashioned way or you will broke the caliper casting.
This new kind of break should be only twisted clockwise to bring the piston back to its position you can use only long nose pliers to rotate the piston since there is two cavity on the piston for this use.
Also after setting the piston back to it's position take care of the seal around the piston be shure before replacing the caliper over the disk that the seal will not go between the disk and the pad...
slide the pads gently to it's position and that's it.

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Going up a hill, traction and break lights comes on (service traction-break fluid) message on my screen, got to top of hill and slowed down, lights came off. 2008 pontiac g6


Make sure your brake fluid is at the correct level. Any issue with the brake system will cause the traction system to not work as traction control works by modulating the brake on the wheel (s) that are slipping. If fluid level is fine then the sensor for the fluid level may be bad.

Jul 27, 2016 | 2008 Pontiac G6

1 Answer

Where is the fuse box on a 2008 Pontiac G6


On this website (link below) you find fuse box diagram and description for Pontiac G6 (2008 - 2009)

Pontiac G6 2008 2009 fuse box diagram Auto Genius

Nov 12, 2012 | 2008 Pontiac G6 Sedan

2 Answers

Im replacing the rear break callipers on a 2008 pontiac g6 sedan i need to know if that big spring will stay in place when i transfer it to the new calliper or do i need a spring tool of some kind


The spring will stay in place. You will need to remove the cable. The worst case is you may have to remove bolts out of the bracket and remove the cable that way as an assembly. Make sure that that holes that are in the piston of the calipersare straight up and down so they line up with the little bumps on the back of the brake pad. That should be the only trick. I would replace brake calipers unless they are either leaking or siezed up. Other than those 2 reasons are only ways for shop and parts houses to make money. Let me know if you need anything else.

Jul 24, 2010 | 2008 Pontiac G6 Sedan

1 Answer

Roaring sound in front wheel pontiac g6 2005


If it is heard all the time it will most likely be a bad wheel bearing. If it is just when braking it will be brake related like worn brake pads and/or rotor.

Jun 02, 2010 | 2005 Pontiac G6

1 Answer

2008 Pontiac G6 Convertible retractable top won't work


2007 Pontiac G6 retractable top engine swithed off while raising, top continued to close in compartment right side upper forward pad looking thing popped and the compartment would not close, however the top will raise and go back in place, cannot leave top in compartment since the trunk lid will not close over the stored top..........

Apr 25, 2009 | 2008 Pontiac G6 Sedan

1 Answer

Pontiac g6 sedan 06 model


2007 PONTIAC G6 CONVERT. BRAKE LIGHTS STAY ON WHILE DRIVING AND GO OFF WHEN PUT BRAKES ON, AND YOU CRUISE CONTROL WILL NOT WORK WHILE BRAKE LIGHTS ARE ON.

Mar 30, 2009 | 2008 Pontiac G6 Sedan

1 Answer

Squeaky Brakes


there is two things that can cause brakes to squeak: brake dust and not having some brake antisqueak on the back of the pads.
you may have to take off the calipers and put some brake antisqueak on the back of the pads and you can get this at any auto store and see if that helps with the squeaking

Mar 11, 2009 | 2007 Pontiac G6 GT Convertible

1 Answer

Rear brake pads


try going to the site below here as well as reading this, it's really helpful and informative, it's a nice step by step. braking systems, when it comes to changing the brake pads hasn't really changed much with modern technology, just remember to used the proper tools to compress all the pistons equally, and also if your pistons have that cross going over the top of them then you have to use a pair of needle nosed pliers to turn the piston counterclockwise this will compress the piston.....hope this and the site are helpful....good luck and happy wrench turning!

http://www.edmunds.com/ownership/howto/articles/43787/article.html

Jan 28, 2009 | 2008 Pontiac G6 Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

784 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...