Question about Saturn SC2

1 Answer

My clutch wont go into neutral 3 4 or reverse or 1st gear

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 162 Answers

Your statement I can hardly understand , any way , check the gare lever to see if you getting the gare with out the engine running
----- now put it in neutral and see if you can get the gare , engine running --- if not there might be aproblem with your clutch ---- how your clutch peddle feel ---- more soft than before / reply

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problems selectin gear in 2009 Holden tk barina it wont go into some gears try puttin it into 1st wont go in then try puttin it in reverse it gos in then lets me go into 1st after selectin reverse 1st


indications are clutch problems
possible clutch cable needs adjusting or replacing
the indications are that the clutch plate is dragging slightly and the gears ore not lining up to mesh until you select reverse or first to stop the shaft turning
If hydraulic system , air in the system and it needs bleeding

Jan 27, 2018 | Holden Cars & Trucks

1 Answer

2001 Saturn SL transmission won't engage


hangon. your leaving something out. myguess is you had the ebrake pulled so the car didn't roll when it was in gear. and now the car wont move at all or what? you left alot of important info out. if it is running and wont move at any point you broke something in the trany or a driveshaft. you should not be able to shift the trany into any gear if the engine is running. the clutch is turning and unless the clutch is disengaged you wont be able to shift. knowing that i am guessing you broke it good and need a new trany

Sep 17, 2017 | Saturn SL Cars & Trucks

1 Answer

4t60e stuck in first gear


Can you shift 1-2-3 and back down 3-2-1 by moving the gear lever by hand?
=======
Any starting problem on P and N?
Check the reverse light and see does it lite while in reverse.
I need to rule out bad neutral safety switch.

Please let me know on reply.

Jan 16, 2014 | 1997 Buick LeSabre

1 Answer

Transmission trouble


Vehicle does not move forward.
The following parts and assemblies need to be checked thoroughly.
1. Manual valve
2. Valve body assembly
3. Forward clutch C1
4. Planetary gear unit
5. 1st and reverse brake (B3)
6. Park/ neutral position switch

Sep 12, 2013 | 2006 Toyota Corolla

1 Answer

Transmission stuck


Clutch hydraulics has air in it or the clutch master cylinder is failing.

Jun 28, 2013 | Volkswagen Beetle Cars & Trucks

1 Answer

Gear Selector or Cables?


Check the selector guide, at the front lower part of the engine has not come loose.

Jun 20, 2017 | 2003 Ford Mondeo

3 Answers

Hard to shift my gears when car in cold.Won't even go out of neutral to 1st gear.Forget about going into reverse.


With the engine off, check your operation of the gear shift. If you can go in and out of the gears fine without the engine running, then you have a worn clutch disc that needs replaced. If the problem still exists then you either have low fluid/weak hydraulic system, or there is a problem with the syncro that may be adjusted.

Nov 02, 2011 | 2006 Ford Focus

1 Answer

Have 1st 2nd and reverse, no drive 1988 model 2 wd


sounds like 3rd gear clutch is out (it might have blew out a lip seal or something)
pull the pan c if there is a lot of black on the bottom of pan (no 3rd = no 4th either) the 3rd gear clutches are engaged along with the 4th gear clutches to make overdrive
if the tcc cable is out of adjustment it mite shift at wot (wide open throttle) max rpm (5000-5500)
if it just 1,2, neutral its probly clutches

Mar 25, 2010 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

1991 Caprice No reverse. Moves in neutral. All forward gears OK.


What engine? Rear wheel drive ?Sounds like shift linkage or cable out of adjustment slightly. Have a look at where cable or rod attaches to transmission for adjustment. If not sure of what your looking for get back to me with info.

Mar 21, 2009 | 1993 Nissan Maxima

3 Answers

97 TJ reverse issue


your syncronizer is going out on the reverse you need to have it looked at soon

Dec 25, 2008 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

Marvin
Marvin

Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...